avital 4103 rs and pkall immobilizer
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=133764
Printed Date: May 13, 2024 at 11:51 PM
Topic: avital 4103 rs and pkall immobilizer
Posted By: jen1110bill
Subject: avital 4103 rs and pkall immobilizer
Date Posted: March 03, 2013 at 3:33 PM
Im installing an avital 4103 remote start on a 1998 ford explorer using the express pkall module and cant seem to find where the blue/white wire on pkall module hooks to the avital unit. The manuel for express kit says to hook to (-) while running wire of avital unit but not sure which wire that is.
Also the xpress module wont program, I get to step 8a which is programming for auto trans which says - press and hold the programming button untill the led flashes once, then release- but the led never blinks, if I let go of programming button the led comes on and stys lit.
Any help is greatly appericated
-------------
BILL
Replies:
Posted By: howie ll
Date Posted: March 03, 2013 at 4:31 PM
Either satellite harness, pin 1 blue or H3 Blue/white labelled either GWR or "status output",
2nd. question, check your wiring and re-read the instructions.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: smokeman1
Date Posted: March 03, 2013 at 4:31 PM
I read that step 8a is activate the remote start is automatic.
-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation
Posted By: howie ll
Date Posted: March 03, 2013 at 4:34 PM
It's not the Xpress module it's the 4103 that won't program.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: jen1110bill
Date Posted: March 03, 2013 at 5:10 PM
Thanks for the info ill recheck my wiring
-------------
BILL
Posted By: jen1110bill
Date Posted: March 04, 2013 at 8:28 AM
Ok have the blue/white wire correctly but another question the pink wire says to wire to ignition of vehicle, would that be ignition wire in switch for tumbler or ign wire at column? Thanks again for the help
-------------
BILL
Posted By: kreg357
Date Posted: March 04, 2013 at 10:00 AM
The PKALL Pink wire can connect to the Avital 4103 thick Pink Ignition wire ( that continues to the Explorers GREEN/ Purple Ignition wire ).
-------------
Soldering is fun!
Posted By: howie ll
Date Posted: March 04, 2013 at 10:16 AM
By definition:-
Ignition wire 0V on key out.
0V on ACC.
12V on ignition.
12V on start.
The wire that runs from the IGNITION SWITCH to various circuits enabling the engine to be started.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: jen1110bill
Date Posted: March 05, 2013 at 7:55 AM
Thanks again for all the help, its been a couple years since doing any install so im a little rusty, just do it to help out freinds and family anymore so sorry if any questions seem repetious or lack of common sense.
-------------
BILL
|