python rs 4103 pljx bypass 2000 gm safari

Hi, First time post hope i do it right. I have been looking for info on your site for help wiring a python 4103 r/s with a xpresskit pljx bypass module on a 2000 gm safari. I have tried different things with no success. Have everything working but it will not remote start. I have tried to start with key in ignition to eliminate the pljx. This is how have it wired as of now. Just want basic functions unlock-lock and remote start.
(Heavy 6 pin) pink-ing 1- to pink,purple-start-to yellow,orange-acc-to orange,pink/white-ing 2-to white,bothe reds to 12v constant.
(H1 9 pin) used only white-light flash,black-ground,brown-horn.all work. And door locks
(H3 5 pin) BLACK/ white-neutral safety-to ground,violet/whtie-tach-to white coil wire,brown-brake-to white brake switch wire,gray and the blue/white wires not used.
Pljx-blue-to yellow,black-to ORANGE / black,violet-to purple and yellow start wires,pink-to pink- ing 1wire,red to 12v constant. Tried brown wire on H1 WHITE/ blue and on the blue of the 4 pin satelite harness no luck. Seemed to take programing.It is a passlock 2 correct have seen list as both 1 an 2 tried jumper in both postions.Tried it wired and un wired with key in the ingnition. I'm I missing something some where. Any help would be appreciated. Thank you. Great site by the way.

-------------
Hilljack2008

What does happen when you try to remote start?   Dash lights come on, but no starter crank?  Starter cranks but quits? Does start but shut off?   Tries to start 3 times and then quits?  Or nothing?  Any parking light flashes? If so how many flashes.

How did you make your connections to the car?  Solder or?????

-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation

It does nothing. The door locks work and the horn honks and lights flash when you lock or unlock. Wires are spliced in very good connections and insulated. Thought maybe there may have been a wire in one of the harnesses that I did not use that I should have used. I read in some of the post that say to cut the starter wire in two and there is no mention of it. Mine is not cut. If it does need cut what wires go to ignition side and what ones go to starter side. Thank you for your time and help.

-------------
Hilljack2008

Are you connections soldered?

Time to get a DMM out to check the outputs of the remote start.  Should have 12 volts showing on the  Pink, Pink/White and Orange at start of remote start, 12 volts should drop form orange during cranking and show 12 volts on purple for cranking. If no voltage, something is not connected correctly.

-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation

Thank you smokeman1. I will check them as soon as I can. May not be till Monday evening. I was searching some more on this site. The WHITE/ blue activation wire from the (h1) 9 pin harness. Does this wire connect to anything or does it need grounded? As of now it's not connected to anything. Once again thank you for your time.

-------------
Hilljack2008

Ok I checked the wires. Nothing happens when I try to remote start no power to pink,pink/white,orange wire.No clicking I mean nothing. There's power to the heavy gage wires when the key is on so connections are good. Tried connecting the yellow wire from 9 pin connector to the pink heavy gage wire still nothing. Remotes are programed. I'm stumped at this point any ideas would be appreciated. Thanks guys.

-------------
Hilljack2008

Did you ground the BLACK/ white (Neutral Safety Switch). (H2/1) in a 5 pin harness I believe

-------------
I drink current, eat ohms, and bleed voltage

BLACK/ white neutral safety wire is grounded with other black ground. Should I post exactly what wires are being used?

-------------
Hilljack2008

Posting all of your wire connectings would be nice.

-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation