viper 4704 no start
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=134535
Printed Date: June 12, 2024 at 2:37 AM
Topic: viper 4704 no start
Posted By: perfecthrasher
Subject: viper 4704 no start
Date Posted: July 13, 2013 at 10:57 PM
Finally I had time to go back and finish 4704 install on my 2008 Nissan rogue key fob type vehicle. My issue is the starter doesn't turn over checked my grounds etc. What i've found is that there is no power to the starter wire at the ignition plug when I attempt a start. There is approx. 12 volts when I use the key fob what I'm I missing?
Thx
Replies:
Posted By: howie ll
Date Posted: July 14, 2013 at 2:55 AM
The heavy duty plug; is there a red, RED / white and RED / black? Are they all connected to a heavy duty (such as ignition loom supply wires) constant?
Has tach been programmed?
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: perfecthrasher
Date Posted: July 14, 2013 at 1:17 PM
I did not connect the RED / white RED / black based on my reading for this vehicle on the forums. I just completed the RED / white RED / black connections redid the tach run and programmed the tach. The vehicle will now turn over (and run) BUT only with the key in the tumbler I gather I have a bypass issue now?
Posted By: offroadzj
Date Posted: July 14, 2013 at 2:41 PM
Yup. What bypass did you use?
-------------
Kenny
Owner / Technician
KKD Garage LLC
Albany, NY 12205
Posted By: perfecthrasher
Date Posted: July 14, 2013 at 3:14 PM
Idatalink ads-al
Ty
Posted By: mmain1
Date Posted: July 18, 2013 at 9:58 AM
I'm not sure if you are using D2D or W2W. If you are using W2W did you connect the Ground While Running input to the Dark Blue Status Output wire?
Posted By: perfecthrasher
Date Posted: July 18, 2013 at 8:38 PM
I'm doing D2D, I can program the bypass but the led is off during remote start attempt (invalid ground when running status from remote starter). Based on the guide 9473 I connected the solid black lines only so no status output wires have been connected.
ty
Posted By: kreg357
Date Posted: July 19, 2013 at 6:58 AM
If running D2D mode to a Viper 4704, was / is the iDatalink bypass module flashed with the DBI flavor of firmware ( not the ADS flavor )?
-------------
Soldering is fun!
Posted By: perfecthrasher
Date Posted: July 23, 2013 at 8:14 PM
flashed iDatalink 2-way DL-NI4
ty
Posted By: kreg357
Date Posted: July 23, 2013 at 8:50 PM
Still not sure if you have the correct firmware.
DBI-AL(DL)-NI4 for ADS-AL CA bypass module is the correct firmware for D2D with a Viper unit.
ADS-AL(DL)-NI4 for ADS-AL CA bypass module will not work D2D with a Viper unit.
Either will work in W2W mode.
-------------
Soldering is fun!
Posted By: perfecthrasher
Date Posted: July 23, 2013 at 9:47 PM
Got it as far as I recall the device type selected was other so the recommended install mode was iDatalink 2 way so I did flash it with the wrong firmware. I'll have another go tomorrow thx Kreg!!
Posted By: kreg357
Date Posted: July 24, 2013 at 3:31 AM
Yes, should be DBI-AL(DL)-NI4-EN version 1.7. Follow the correct diagram in install guide #10934 and set the
ADS AL-CA's Installation mode to Type 1 ( one Blink - Data Mode ) & lock it in for D2D communications with the Viper.
-------------
Soldering is fun!
Posted By: perfecthrasher
Date Posted: July 27, 2013 at 6:32 PM
Thx again Kreg I hurt my back was out for a week just go off my ass did a reflash works!! Going to cleanup some of the wiring but again all appears to be good thankyou very much!!
|