99 windstar
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=134638
Printed Date: July 03, 2025 at 3:22 AM
Topic: 99 windstar
Posted By: eddiec
Subject: 99 windstar
Date Posted: July 31, 2013 at 2:22 PM
I have a 99 Windstar that has the factory keyless entry. It didn't come with any remotes so I ordered a new remote and tried to program it per the instructions. The instructions say to go from off to run 8 times leaving the key in run on the 8th time. I have tried this several times and cannot get the locks to lock/unlock to confirm programming mode. I am wondering if anyone has any ideas for troubleshooting the system. The dealer is absolutely no help unless I want to pay them $63 hr. to diagnose with 1 hour minimum. With help from this site I was able to install a remote start alarm in my grand cherokee so I have some knowledge of vehicle electronics. Also I am hoping someone can tell me how many plugs should be going to the keyless module behind the glovebox. It has 3 slots but only one has a plug. The van has power locks and dual power sliding rear doors if that helps. Also, no keyless pad on door. Thanks in advance for any help!
Replies:
Posted By: pts760
Date Posted: July 31, 2013 at 3:08 PM
Where did you order the remote from?
-------------
I drink current, eat ohms, and bleed voltage
Posted By: eddiec
Date Posted: July 31, 2013 at 9:53 PM
It was a new factory remote bought off ebay.
Posted By: lucasoil4u
Date Posted: August 01, 2013 at 11:53 AM
Famous last words. EBAY. What kind of remote start is it?
Posted By: eddiec
Date Posted: August 01, 2013 at 12:17 PM
Its a factory keyless entry system. Remote is OEM 5 button remote brand new. The problem is that the factory keyless entry system on the van will not go into program mode. I am hoping someone can give me some direction as far as troubleshooting factory keyless entry or at least if someone owns or is working on a 99 windstar how many plugs the module behind the glovebox has connected to it. Thanks for any help in advance.
Posted By: eddiec
Date Posted: August 01, 2013 at 12:19 PM
Forgot to say its not remote start or anything. I am just trying to get the factory system working.
Posted By: eddiec
Date Posted: August 01, 2013 at 7:19 PM
Just wanted to add that it looks like the van had an aftermarket alarm installed at some point. While trying to trace wires I can see that some of the ignition wires and others have been tapped into. I didn't see any cut wires or anything but I'm wondering if they disconnected/cut a wire(s) going to the keyless module. If anyone has any suggestions I would greatly appreciate it.
Posted By: smokeman1
Date Posted: August 02, 2013 at 12:21 PM
You could try this procedure. It states to cycle the ignition 5 times. Worth a try.
https://www.fixya.com/cars/t2254317-2000_ford_windstar_keyless_entry_remote
I have a 2000 Taurus and it is 8 cycles of the key to get to programing. The lock cycle right away on the 8th cycle og the ignition. ------------- When all else fails, Read the Instructions
Support the12volt.com Make a Donation
Posted By: eddiec
Date Posted: August 02, 2013 at 4:46 PM
Thanks for the info! I've read that also. I tried 8 times, 5 times, and 7 times. Nothing has worked. I think the previous owner either fried or disconnected the keyless module. I wish I could get a diagram of the keyless entry system. Is it possible to have the system deactivated by the dealer like with the automatic locks?
|