python 5210p xpressstart one
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=135036
Printed Date: May 31, 2024 at 9:40 PM
Topic: python 5210p xpressstart one
Posted By: iono2013
Subject: python 5210p xpressstart one
Date Posted: October 08, 2013 at 7:51 PM
Hi everyone,
I had a 2012 Toyota Camry w/o smartkey, I try install R/S over the weekend and everything seem to working just fine except when I try to r/s its doesn't crank, but the dashboard light and everything is on then turn off after a few second. I meter the starter wire (purple) when I r/s it doesn't get any voltage reading at all, I just wondering what was the problem?
Replies:
Posted By: smokeman1
Date Posted: October 08, 2013 at 8:35 PM
It might help it you list all of your connection from the unit to your car.
I don't have a install guide for this unit, but are all three of the heavy gauge, FUSED wires, connected to a 12 volt source?
-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation
Posted By: iono2013
Date Posted: October 08, 2013 at 9:07 PM
yes
(H4) 8 thick-gauge wires (relay pack) vehicle wire
H4/1 - pink/white(+) ignition 2 / flex relay output - pink
H4/2 - RED / white (+) fuse (30a) ignition 2/flex relay input- green 12v
H4/3 - pink (+) ignition output - black
H4/4 - red (+) 12 volt input - green 12v
H4/5 - orange (+) accessory output - white
H4/6 - red (+) 12 volt input - green 12v
H4/7 - green starter input (from key switch) ** - not use
H4/8 - violet (+) starter output (to starter) - blue
Posted By: iono2013
Date Posted: October 08, 2013 at 9:11 PM
I just realize the car has 2 starter wire which is start 1 (blue) which I make connection to and start 2 ( lt green) ? do i have to use both wires for it to work?
Posted By: smokeman1
Date Posted: October 08, 2013 at 9:48 PM
Most likely. You will have to use the (-) Starter from a different harness with a relay for the second starter, since you have used the flex relay output for the second ignition.
-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation
Posted By: iono2013
Date Posted: October 08, 2013 at 10:05 PM
I kind of got the idea, but one thing I don't understand is that the starter wire from r/s not sending voltage? even though I didn't have the second starter wire hook up, at least the voltage present...right?
Posted By: smokeman1
Date Posted: October 09, 2013 at 5:55 PM
It would seem so. I don't have the documentation for that model, so not sure what wire is for what. Just kinda going from a photo of the unit and the past wiring scheme from DEI
-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation
Posted By: 03lxv6
Date Posted: November 21, 2013 at 6:12 PM
Kind of a late response but I had the same issue with my 2007 Accord. There is only 1 starter wire in my car. The Purple wire would only go to .01 voltage during RS.
I reset my module and reflashed and it finally cranked. I think it has to do with Virtual Tach.
The firmware seems buggy though. Sometimes I don't get the light flash and other times the horn doesn't honk. I'm running D2D so I didn't connect any of those wires directly. They should work like OEM through CAN.
|