viper 5704v on 94 lexus
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=135668
Printed Date: May 03, 2024 at 6:24 AM
Topic: viper 5704v on 94 lexus
Posted By: lowriderman234
Subject: viper 5704v on 94 lexus
Date Posted: December 30, 2013 at 10:34 PM
Does anyone know what wires are required for the whole system install? I can't seem to get the remote start to work.
Replies:
Posted By: lowriderman234
Date Posted: December 30, 2013 at 10:35 PM
It's a 1994 Lexus ES300
Posted By: chev104275
Date Posted: December 31, 2013 at 6:07 AM
Ready remote.com or bulldog security.com should have the diagrams
Can you list out the connections you've already made.
-------------
If i Can't Install it I Don't need it Joe
Posted By: lowriderman234
Date Posted: December 31, 2013 at 9:50 AM
H1/1 red constant 12v to WHITE/ red
H1/2 black ground
H1/3 siren output
H1/4 parking light isolation -not used
H1/5 parking light output -can't locate the wire inside car...
H1/6 not used
Door locks are wired up correctly
H3/1 pink wired to B/Y ignition wire
H3/2 R/W -not used
H3/3 Accessory wired to P/B wire
H3/4 starter output connected to car side B/W
H3/5 starter input connected towards key side B/W
H3/6 connected to 12 volt constant
H3/7 connected to second ignition B/O
H3/8 -not used
H3/9 tapped to 12 volt constant
Haven't start to wire the second harness yet I did attempt to ground the H2/13 BW wire but nothing still...
Posted By: chev104275
Date Posted: December 31, 2013 at 10:49 AM
PARKING LIGHTS ( + ) GREEN/ BLACK (+) @ DIMMER SWITCH
Sorry I don't have the guide handy for that system what is the H3/2 , H3/8 ?
What happens when you try and remote start it ?
-------------
If i Can't Install it I Don't need it Joe
Posted By: lowriderman234
Date Posted: December 31, 2013 at 3:18 PM
H3/2 = (+) fused 30 a ignition 2 / flex relay input 87
H3/8 = (+) flex relay input 87a key side (if required) of flex relay
The remote says error and the module makes about 8 clicks
Posted By: chev104275
Date Posted: December 31, 2013 at 4:13 PM
I believe 8 is manual trans mode or neutral safety ? Did you program the system for auto trans ? Is the override switch plugged in ? If auto trans Is the BLACK/ white neutral safety wire grounded ? If manual trans is it to the e brake
-------------
If i Can't Install it I Don't need it Joe
Posted By: lowriderman234
Date Posted: December 31, 2013 at 4:47 PM
No, the system won't go into program mode, it always goes into valet when i do it. B/W neutral safety wire is grounded and whats the override switch?
Posted By: chev104275
Date Posted: January 01, 2014 at 8:23 AM
Press unlock on the remote before trying to get into programming.
There should be a switch that plugs into the main brain inbetween the main 6 pin connector and the door lock connector.
How are you trying to get into programming ? Key on key off press and hold programming button until the siren chirps the menu number your looking for
-------------
If i Can't Install it I Don't need it Joe
Posted By: nyberg
Date Posted: January 01, 2014 at 12:43 PM
chev104275 wrote:
I believe 8 is manual trans mode or neutral safety ? Did you program the system for auto trans ? Is the override switch plugged in ? If auto trans Is the BLACK/ white neutral safety wire grounded ? If manual trans is it to the e brake
this should be your problem, just got this "fault code" today,
u have a metall switch u plug into alarm, u can choose on/off
Posted By: smokeman1
Date Posted: January 01, 2014 at 1:06 PM
Do you have the parking lights connected? You stated the module makes ABOUT 8 clicks. Need to know exactly how many.
The parking lights flashing the number of clicks works better.
Also need to connect the H3/2 RED / white to a constant 12 volt source. This is the input for the H3/7 pink/white output to ignition 2.
See video: https://youtu.be/uq1ETQxMp7M
-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation
Posted By: lowriderman234
Date Posted: January 01, 2014 at 10:45 PM
Yes I've tried the key on key off and holding down the control center button but nothing happens.. So I need a total of 3 wires hooked up to a constant 12v? I have only two constant 12v and it's white and WHITE/ red. The alarm part is hooked up to there, so would 3 more wires there be dangerous?
Posted By: smokeman1
Date Posted: January 02, 2014 at 6:28 AM
Is your car Automatic or manual?
Yes. H3/2,6, and 9 need to be connected to a constant 12 volt source. If you have two 12 volt wires, just split all of your connection between the two.
Go to the download section and get the Viper 5701 install manual. On page 60 there is a better explanation of how to get into the menus and make changes.
Take the H2/6 Green wire and put it to a chassis ground. This is the (-) Neg door trigger. The brain needs to see it along with the key ON/OFF to get into the menus. It will take a number of tries for you to get it as it can be tricky.
-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation
|