Print Page | Close Window

2013 mazda 5 factory alarm

Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=135863
Printed Date: March 28, 2024 at 12:20 PM


Topic: 2013 mazda 5 factory alarm

Posted By: racingtoys
Subject: 2013 mazda 5 factory alarm
Date Posted: January 18, 2014 at 10:49 PM

HI
Im trying to create a custom home made alarm for a Mazda 5 does anyone have the wiring colors and location for the factory alarm system and remote start.

Thanks a lot



Replies:

Posted By: racingtoys
Date Posted: January 22, 2014 at 12:32 AM
Does anyone have this please
Thanks




Posted By: chev104275
Date Posted: January 22, 2014 at 5:45 AM
DIRECTWIRE™ WIRING INFORMATION - MAZDA / MAZDA5 / 2013 / Remote Start

12volts blue/black (40A) + ignition switch, white 8 pin plug, pin 8

Starter blue/red + ignition switch, white 8 pin plug, pin 5
     
Ignition blue + ignition switch, white 8 pin plug, pin 1
      
Accessory BLACK/ red + ignition switch, white 8 pin plug, pin 6

Second Accessory BLACK/ white + ignition switch, white 8 pin plug, pin 7

Keysense blue + ignition switch, white 8 pin plug, pin 2

Power Lock blue -1000 ohms either kick or BCM behind glove box, white 24 pin plug (6), pin 14

Power Unlock (same as power lock) -

Lock Motor RED / blue to RED / yellow 5 wire either kick or BCM behind glove box, white 16 pin plug (5), pin 8

Unlock Motor RED / black 5 wire either kick or BCM behind glove box, white 16 pin plug (5), pin 7
Parking Lights+ blue/black + passenger kick, harness to rear

Parking Lights- BROWN / red - headlight sw or BCM behind glove box, blue 24 pin plug (2), pin 23

Hazards blue / YELLOW - hazard sw or BCM behind glove box, blue 24 pin plug (2), pin 7

Turn Signal(L) BLACK/ red + pass kick or BCM behind glove box, white 16 pin plug (5), pin 3

Turn Signal(R) RED / white + pass kick or BCM behind glove box, white 16 pin plug (5), pin 2

Reverse Light blue/white + pass kick or BCM behind glove box, gray 24 pin plug (1), pin 9

Door Trigger WHITE/ blue - N.C. either kick or BCM behind glove box, white 24 pin plug (6), pin 4

Dome Supervision yellow/black - pass kick or BCM behind glove box, white 16 pin plug (5), pin 15

Trunk/Hatch Pin RED / black - pass kick or BCM behind glove box, white 24 pin plug (6), pin 15

Hood Pin gray - N.C. BCM behind glove box, gray 24 pin plug (1), pin 17

Trunk/Hatch Release purple / YELLOW (rear handle switch) - pass kick or BCM behind glove box, white 24 pin plug (6), pin 8
    
Factory Alarm Arm blue/orange (driver door key lock) - either kick or BCM behind glove box, white 24 pin plug (6), pin 2

Factory Alarm Disarm lt. GREEN/ red (driver door key unlock) - either kick or BCM behind glove box, white 24 pin plug (6), pin 13

Disarm No Unlock (transponder and ignition)
     
Tachometer BLACK/ white, BLACK / YELLOW, BLACK/ blue, or blk/org ac any fuel injector, white 2 pin plug, pin 1
     
Brake Wire RED / yellow + brake switch, white 4 pin plug, pin 4

Parking Brake brown - pass kick or BCM behind glove box, blue 24 pin plug (2), pin 9

Horn Trigger PURPLE / white - horn switch or BCM behind glove box, blue 24 pin plug (2), pin 11

Memory Seat 1 N/A     
Memory Seat 2 N/A     
Memory Seat 3 N/A     
Interface Modules: Not Available



      
This wiring information is being provided free of charge on an "as is" basis, without any representation or warranty. It is your responsibility to verify any circuit before interfacing with it using a digital multimeter.
Directed electronics, Inc. assumes no responsibility with regards to the accuracy or currency of this information. Proper installation in every case is and remains the responsibility of the installer. DEI assumes no liability or responsibility resulting from improper installation, even in reliance upon this information.





-------------
If i Can't Install it    I Don't need it   Joe




Posted By: racingtoys
Date Posted: January 22, 2014 at 9:26 AM
Thanks!!




Posted By: gerardo30
Date Posted: March 17, 2015 at 11:55 PM
HI
I'm trying to Install the module for folding mirror for a Mazda 2 2012 does anyone have the wiring colors and location for the factory.

Thanks a lot





Print Page | Close Window