compustar cm6000 2 way remote beep
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=136464
Printed Date: April 20, 2024 at 2:13 AM
Topic: compustar cm6000 2 way remote beep
Posted By: jdmegcoupe
Subject: compustar cm6000 2 way remote beep
Date Posted: April 16, 2014 at 3:27 PM
Hello all I am in the process of finishing the install on my RSX with a CM6000-AS and 2 way remote SS kit. I am having one issue which is when I arm the system I get 3 chirps from the siren and horn and the remote beeps a bunch of times and the lights on the remote flash. I have taken this video so as to make it as clear as possible...
I have disconnected the hood and trunk wires at the control module of the cm6000 and when i arm the car i get this
Everything is closed...
Also when I connect the op500 it reads err 1 fail
can someone help me please. -------------
Replies:
Posted By: jdmegcoupe
Date Posted: April 17, 2014 at 10:16 AM
Please can anyone help me on this? I need to get this done ASAP
-------------
Posted By: enice
Date Posted: April 17, 2014 at 3:39 PM
op500 will fail when the system is armed. disarm and then plug in. Plus i don't see the video. its not showing
-------------
Eric
Audiomaxx
528 East Fordham Road
Bronx NY 10458
Compustar Top Gun Dealer Award 2012-2013
Posted By: jdmegcoupe
Date Posted: April 17, 2014 at 3:41 PM
I have the system disarmed and have tried to use the op500 with no luck
ok here is the link for the video
 -------------
Posted By: jdmegcoupe
Date Posted: April 17, 2014 at 3:43 PM
Posted By: jdmegcoupe
Date Posted: April 17, 2014 at 3:58 PM
youtube video-------------
Posted By: enice
Date Posted: April 17, 2014 at 10:39 PM
I have never seen that issue. Reprogram the remote and or reflash the brain on the idatalink website.
-------------
Eric
Audiomaxx
528 East Fordham Road
Bronx NY 10458
Compustar Top Gun Dealer Award 2012-2013
Posted By: jdmegcoupe
Date Posted: April 17, 2014 at 10:48 PM
Ok I will try that in the morning.... I think it might have to do with the door pin switches and the door triggers when I was closing up the car and leaving the garage I closed it all up and it did it again I disarmed it and opened the pass door then armed it and the system chirped 3 times but it didn't show the doors open on the remote....
-------------
Posted By: kreg357
Date Posted: April 17, 2014 at 11:21 PM
I believe the problem is that the Compustar is seeing the Hood Pin input signal at Chassis Ground when you press the Lock button.
While we are not comparing apples to apples, I get similar results on a FT6200-s install I did today if I raise the hood and hit the
Lock button. The first Lock press will flash the Parking Lights three times ( instead of once). The second Lock press will flash the
Parking Lights three times and beep the horn three times ( instead of once). Triple check the Compustar to ensure that the Hood Pin
input wire is not connected to chassis ground.
-------------
Soldering is fun!
Posted By: jdmegcoupe
Date Posted: April 22, 2014 at 3:50 PM
Okay I have been sick for the last 4 days.... Today i went out to the car and i tapped the drivers door pin switch with a wire and did the same to the pass side, then i put 2 diodes tied both of the anode sides together and connected that to the CN3 Pin 10 RED / white cable at the control module, then the wire from the pass side door to one of the cathode sides of one of the diodes and the drivers side to the other diode, I closed the hood and closed the doors and its still beeping 3 times when I arm and lock
-------------
Posted By: dswift
Date Posted: May 09, 2014 at 1:12 PM
Looks like parking light reminder to me. There 3 parking light wires on the 6000. (+) pk lights and (-) pk light Outputs. There is also a ORANGE / Blk which is the (-) pk reminder Input that you do not need.
Send me all the I/O's that you have connected and this will be an easy fix.
-------------
"dont ground out!"
Posted By: jdmegcoupe
Date Posted: May 09, 2014 at 1:38 PM
Thanks I figured it out just forgot to post it up...
The RSX hatch pin is connected to the hatch light and when it's open it's +12v and ground when close so the alarm thought the hatch was open... I wired it a diode with the cathode facing the toward the hatch pin and it fixed the issue
-------------
Posted By: dswift
Date Posted: May 09, 2014 at 4:03 PM
I was just looking for the "like" button.
-------------
"dont ground out!"
|