full wiring for compustar cm7000as
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=136522
Printed Date: April 25, 2024 at 6:08 AM
Topic: full wiring for compustar cm7000as
Posted By: jdmegcoupe
Subject: full wiring for compustar cm7000as
Date Posted: April 26, 2014 at 7:30 AM
Hello I just got a Cm7000AS and I would like the full wiring for it. I dont have access to computech3.com. If anyone could help I would appreciate it.
-------------
Replies:
Posted By: jdmegcoupe
Date Posted: May 01, 2014 at 7:38 AM
Hello, I meant the full install manual for the CM7000AS, or 7AS, or FT-7000AS-CONT
-------------
Posted By: kyousif
Date Posted: May 04, 2014 at 12:49 PM
try this https://www.compustar.com/dealersupport/ you can download the one for the cm6000 it should be very similar. You should have the CM7000 wiring schematic in the box and the unit itself has the wire label on back. You can download a vehicle tech sheet free at www.bulldogsecurity.com or www.commandocaralarms.com or here as well.
If you have a newer vehicle a lot of the wiring is not needed with the Blade-AL cartridge www.idatalink.com and that will tell you which few wires you need.
Good Luck. Im just a newb DIYer
Posted By: jdmegcoupe
Date Posted: May 05, 2014 at 7:53 AM
Thanks for replying.... the CM7000 is completely different from the Cm6000
-------------
Posted By: kyousif
Date Posted: May 05, 2014 at 4:17 PM
I have them both. They all have similar features functions and etc. ANYWAYS go here this is what you want. You can get your manual and firmware hopefully you have the idatalink ads-usb updater and an OP500. Programming sucks without the OP500. Good Luck! Hope this helps
Ken
https://techfeed.compustar.com/con_70.php
Posted By: jdmegcoupe
Date Posted: May 05, 2014 at 5:01 PM
Thank you Ken! Thats what I was looking for! I have a OP500 but it keeps saying err 1 and everything is connected
-------------
Posted By: kreg357
Date Posted: May 05, 2014 at 7:37 PM
ERR 1 means that the Compustar's last function was a "Lock" ( or the Compustar is locked ). Do a "Unlock", then unplug the antenna harness and plug-in the OP-500.
-------------
Soldering is fun!
Posted By: jdmegcoupe
Date Posted: May 05, 2014 at 7:39 PM
Did that and still the same...
-------------
Posted By: kreg357
Date Posted: May 05, 2014 at 8:03 PM
Strange, that's what it means on the older series units. Haven't played around with a FT7000 series yet.
-------------
Soldering is fun!
Posted By: dswift
Date Posted: May 09, 2014 at 12:57 PM
Plug it in to the top of OP500 not the bottom.
-------------
"dont ground out!"
Posted By: jdmegcoupe
Date Posted: May 09, 2014 at 1:04 PM
I will try that tonight and see if it works
-------------
Posted By: dswift
Date Posted: May 09, 2014 at 4:02 PM
Well if you were plugging it in the bottom, yes it will work. The bottom input is to update the programmer. There are two inputs on the top. One dedicated to a 4pin antenna male connector and the other for the 6 pin configuration.
 ------------- "dont ground out!"
Posted By: basovienes
Date Posted: May 23, 2014 at 2:28 PM
jdmegcoupe wrote:
Hello I just got a Cm7000AS and I would like the full wiring for it. I dont have access to computech3.com. If anyone could help I would appreciate it.
here...https://techfeed.compustar.com/doc_mans.php
|