DEI 530T Channel 2 delay
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=13739
Printed Date: November 04, 2025 at 4:33 AM
Topic: DEI 530T Channel 2 delay
Posted By: good vibrations
Subject: DEI 530T Channel 2 delay
Date Posted: May 20, 2003 at 12:03 AM
I've just installed a 790 with one 530T for the front windows. My problem is that I want one button on the remote to crack the windows without delay, then if I hold it for 1.5 seconds, it should roll them down completely. As of now, I have to hold the channel two button for 1.5 seconds to get the windows to crack, and 4.5 seconds to get them to roll down. I tried channel 4 with the same results. Do I need a Bitwriter to remove the delay in channel 2? Also, where can I pick up the hard/soft ware to program my alarm via computer? Thanks -Matt
Replies:
Posted By: cpgoose
Date Posted: May 20, 2003 at 8:09 AM
I put my 530t on a different channel just for that reason. I'm not sure how the 790 is, but on my alarm, channel 2 is for the trunk release, so it has a 2 second delay automatically. I put my 530 on channel 4, so there's no delay.
Posted By: good vibrations
Date Posted: May 20, 2003 at 9:06 AM
I tried it on channel 4, but the remote was configured where I had to push two buttons simultaneously for channel 4. The delay was still present. Maybe if I reconfigure the remote to perform channel 4 with a single button push then there won't be any delay. I'll try it today, but if anyone else is familiar with this please let me know. Thanks.
Posted By: cpgoose
Date Posted: May 20, 2003 at 9:19 AM
Yea, I reprogrammed mine for "Auto Learn Single Button Arm/Disarm Configuration". #1 is lock/unlock/panic, #2 is the trunk (delay), #3 is the remote start, and #4 is the windows (no delay).
(Like on page 33 of the 790xv's install manual).
Posted By: rudbwoy69camaro
Date Posted: June 26, 2003 at 8:48 PM
I am going to do the same with my Matrix RS3. I want to use channel 2. I have the bitwriter. Will I be able to change the setting to "no delay" for channel 2? Please let me know. Thanks ! -------------
Posted By: auex
Date Posted: June 26, 2003 at 8:53 PM
Channel two cannot be adjusted or changed, channel 3/4 can be adjusted to validity(on as long as you hold the button), latched(on until you turn it off or choose of with ignition), or a 30 second latched. Check the settings for channel four of your alarm's, if they are something different then validity then change them to validity.
-------------
Certified Security Specialist
Always check info with a digital multimeter.
I promise to be good.
Tell Darwin I sent you.
I've been sick lately, sorry I won't be on much.
Posted By: rudbwoy69camaro
Date Posted: June 26, 2003 at 10:59 PM
Upon arming, no matter what channel, the windows will roll up? Just as long as it's connected to the orange ground when armed? -------------
Posted By: Spawn_X
Date Posted: June 26, 2003 at 11:05 PM
have you tried switching the jumpers up on the module ?
Posted By: Spawn_X
Date Posted: June 26, 2003 at 11:06 PM
rudbwoy69camaro wrote:
Upon arming, no matter what channel, the windows will roll up? Just as long as it's connected to the orange ground when armed?
make sure you put a diode on or you might drain your battery.
Posted By: rudbwoy69camaro
Date Posted: June 27, 2003 at 8:42 AM
Ohh yeah I have diodes. I bought 100 of them of ebay for $1.99. The 1N4004, 1 amp. MANY deals on ebay ! 
-------------
Posted By: cpgoose
Date Posted: June 27, 2003 at 8:48 AM
I only have 1 dioded on the orange wire because I use it for the window module and for the starter kill. Are you using a diode in another spot? I'm assuming you mean that you use the diode so that it doesn't keep drawing power from the battery after the windows have rolled up?
Thanks! ------------- Q: What's the best nation in the world?
A: Donation! Donate to the12volt.com
|