avital 4301 not working

I had a viper 550 esp alarm and i uninstalled it and hooked up the 4103. every thing i needed is connected except the satalite relay ( read some where i didnt need this) and nothing is working, no sound when i hit the door locks or the remote start but when you hit the valet switch the light on the alarm does come on. i trtied to do the remote programing and started the key hit the button once let go hit again and pressed the lock key let go turned off key and didnt work also the horn didnt sound

any ideas?

forgot to mention i have a 99 isuzu vehicross

can you list out your connections so we can get a better look at what's going on

-------------
If i Can't Install it    I Don't need it   Joe

ok hooked up on the 3 pin blue and greenshich are lock unlock

6 pin hooked up all wires high current 12v, output to second ignition,high current 12v, accessory circuit,starter circit, and primary ignition circuit
on satellite harness nothing hooked up

on remote start 5 pin hooked up neutral safety switch ,tachometer input, brake shutdown,

did i miss something? should this come already programed? if not how do i program it?

thanks

zadam123 wrote:

---

ok hooked up on the 3 pin blue and greenshich are lock unlock

6 pin hooked up all wires high current 12v, output to second ignition,high current 12v, accessory circuit,starter circit, and primary ignition circuit
on satellite harness nothing hooked up

on remote start 5 pin hooked up neutral safety switch ,tachometer input, brake shutdown,

did i miss something? should this come already programed? if not how do i program it?

thanks

---

also on the 9 pin i hookied up horn and groun d and light flash output, which are brown, black and white

anyone????

Trying to follow what you have done but it's hard to read could you do something like this

4103.       Truck
6 pin connector

Red. White

Red. WHITE/ black

Purple.      BLACK/ white

Orange.    Blue

-------------
If i Can't Install it    I Don't need it   Joe

ok sorry

9 pin
black - I grounded
white - GREEN/ YELLOW
brown - horn (dont remember color

3 pin
blue - RED / black
green - RED / white

6 pin
red -white black
pink/white - RED / black
red - red white
orange - blue
purple - black white
pink - black yellow

5 pin
black white - dont remember have to look
violet white - red black
brown - red blue

Ok did you meter everything before you connected your wiring ? I've never done this particular truck but according to my diagrams some of your wires may be wrong but the diagrams could also be wrong. The BLACK/ white on the 5 pin harness needs to see ground for the truck to start.

ISUZU VEHICROSS

VEHICROSS      1999-2002

PART      COLOR      LOCATION      DIAGRAM
12 VOLT CONSTANT      WHITE (+) and WHITE/ BLACK (+)      IGNITION SWITCH HARNESS     

STARTER      BLACK/ WHITE (+) or WHITE/ BLUE (+)      IGNITION SWITCH HARNESS     
     
IGNITION 1      BLACK / YELLOW (+) or BLACK/ RED (+)      IGNITION SWITCH HARNESS     

IGNITION 2      BLACK/ RED (+) or BLACK / YELLOW (+)      IGNITION SWITCH HARNESS     

ACCESSORY /HEATER BLOWER 1      BLUE (+)      IGNITION SWITCH HARNESS     
       
PARKING LIGHTS ( - )      YELLOW (-) or GREEN/ YELLOW (-)      @ HEADLIGHT SWITCH
     
PARKING LIGHTS ( + )      GREEN/ RED (+)      IN DRIVERS KICK PANEL
     
POWER LOCK      RED / WHITE (TYPE B)      IN DRIVERS DOOR HARNESS
     
POWER UNLOCK      RED / BLACK (TYPE B)      IN DRIVERS DOOR HARNESS
     
LOCK MOTOR WIRE      LIGHT GREEN (+)      IN DRIVERS DOOR HARNESS     

DOOR TRIGGER      RED / GREEN (-)      IN PASSENGER KICK PANEL     

DOMELIGHT SUPERVISION      USE DOOR TRIGGER, Requires Part #775 Relay
     
HORN      GREEN (-) or ORANGE / BLACK (-)      @ STEERING COLUMN HARNESS     

TACH      BLACK/ RED      @ PCM, See NOTE *1     
     
BRAKE      RED (+)      @ SWITCH ABOVE BRAKE PEDAL     

NOTE *1 the PCM (Powertrain Control Module) is located in the CENTER CONSOLE.




-------------
If i Can't Install it    I Don't need it   Joe