excalibur rs360edpb won’t start
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=138031
Printed Date: May 20, 2025 at 4:05 PM
Topic: excalibur rs360edpb won’t start
Posted By: keny01998
Subject: excalibur rs360edpb won’t start
Date Posted: December 23, 2014 at 1:13 AM
Dear All,
After 28 hours of installing and checking my install, the Excalibur RS-360EDPB with Omega Blade Al2 won't start. I can lock/unlock the door, unlock the trunk. Please help!
This is for 2010 Lexus HS250h.
I flashed the firmware to DL-TL2 for Lexus with my Omega Blade, update RS-360EDPB to latest firmware and follow the diagram from Omega Web Link as follow:
Type 3 wiring diagram:
1. 2 constant 12V RED / RedWhite(+)from remote start to Pin 1(White) 12V on the ECU.
2. Ignition input/output (Pink) #1 from remote start to Pin 2 of ECU 40 pin connector
3. Starter (Violet).......No connection
4. Ignition output (pink/white) #2 ........no connection
5. Accessory Output (orange)........no connection
**Omega states "Do not connect any other acc, ignition, starter from remote starter to the car, the bypass will handle from PTS circuit."
From Omega 20 pin connectors:
1. Yellow RX and GREEN/ Red Rx to Pin 4 RX in the ECU
2. ORANGE / White TX to Pin 16 in the ECU
3. BROWN / Red CANHIGH to CANH pin 6 in the OBDII plug
4. BROWN / Yellow CANLOW to CANLOW pin 14 in the OBDII plug
5. ORANGE / Black Ground (-) to Ground without OEM Hood Switch.
6. Blue/Red Ground (-) to Ground
7. Blue / YELLOW PTS(-) output. No connection because don't need idle mode desired
From Excalibur 18 pin connector:
1. WHITE/ black parking light (-) to Pin 30 in the RX/TX ECU
2. Black ground (-) input to Ground
Remote start is clicking when I try to hit start from keyfob but the car won't turn on. I can lock/unlock doors, unlock trunk fine.
Please go over what I list and tell me what I missed. Do I need to install Hood switch? What about Ignition 2, Starter, Access? The diagram is not cleared about them.
Thanks in advance
Replies:
Posted By: tedmond
Date Posted: December 23, 2014 at 7:15 AM
close all doors and try to start. check to see if yhe unit has a neutral safety wire as well, if it does then ground it
-------------
Ted
2nd Year Tier 1 Medical School
Still installing as a hobby...pays for groceries
Compustar Expert
Posted By: keny01998
Date Posted: December 23, 2014 at 8:09 AM
tedmond wrote:
close all doors and try to start. check to see if yhe unit has a neutral safety wire as well, if it does then ground it
Man, I can say you are my hero. Why I missed a little thing like that? As long as I connect the ground, the car starts. I don't know how happy I was when the thing works.
Thank you very much and Merry Xmas to you
Posted By: keny01998
Date Posted: December 23, 2014 at 10:22 AM
I have another problem with 2010 Lexus HS250H Hybrid Push to Start
The car starts fine with remote start after I connect the black neutral safety ground cable. However, when I open the door, the engine won't shut down and I can't shift to gear. (No takeover with Lexus/Toyota)
What cable do I need to connect? I almost reach my goal. Please help
|