avital 4103 1996 lincoln towncar

Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=138144
Printed Date: May 29, 2024 at 4:20 AM

Topic: avital 4103 1996 lincoln towncar

Posted By: coyn11
Subject: avital 4103 1996 lincoln towncar
Date Posted: January 04, 2015 at 10:57 PM

Tomorrow I am digging into the install. I'm just wanting to check all my wiring. I'm probably forgetting something. Also, do I need relays? Diodes?

Main Harness (H1), 9 Pin connector

Factory disarm - drk grn/prpl
NC
ignition out(to alarm) - to ignition BROWN / pink
activation input - NC
ground when locked/antigrind output - NC
Horn output - Drk Blue
trunk release - to purple / YELLOW
ground - chasis ground
light flash output - brown

Door Lock - 3 pin connector

unlock - to pink/light green
empty
lock - to pink / YELLOW

Heavy Gauge Relay H2, 6 pin connector

output to primary ignition circuit - BROWN / pink
output to starter circuit - WHITE/ pink
output to accessory circuit - BLACK/ light green
30A high current 12v input - light green
output to second ignition / accessory circuit - pink/black
30A high current 12 v input - light green

Satellite harness - 4 pin connector

status output - NC
accesory output - BLACK/ light green
starter output - WHITE/ pink
ignition output - BROWN / pink

Remote start Harness H3 5 pin connector

neutral safety switch input - grounded
tach input - pink @EDIS module
brake shutdown input wire - light green @ brake
hood pin switch shut down wire - to hood pin
second status/rear defogger - I want this hooked up, but i dont know where it goes.

-------------
NOOB

Replies:

Posted By: chev104275
Date Posted: January 05, 2015 at 4:54 AM

On H1 ignition out doesn't go to anything, satellite harness doesn't go to the ignition harness. The satellite harness has all negative outputs made to run external relays.

Door locks are positive trigger and the 4103 has negative outputs you will need a pair of relays or a dei 451m

POWER LOCK      PINK / YELLOW (TYPE A)      IN DRIVERS KICK PANEL
POWER UNLOCK      PINK/LIGHT GREEN (TYPE A)      IN DRIVERS KICK PANEL

-------------
If i Can't Install it    I Don't need it   Joe

Posted By: coyn11
Date Posted: January 05, 2015 at 12:04 PM

First off, Thank you Chev for the reply.
Second, on the cheat sheet I printed off I saw 3 ignitions. How do I hook then up?

Ign 1- primary ignition - BROWN / pink
Ign 2- heat/ac - pink/black
Ign 3- blower motor - BLACK/ lt gen

-------------
NOOB

Posted By: tedmond
Date Posted: January 05, 2015 at 12:58 PM

The 4103 has 2 ignition outputs. The third you'll need the negative ignition wire from the satellite harness; and connect that to a relay as follows

85 negative ignition output
86 constant 12v fused
87 constant 12v fused at 15-20 amps
30 third ignition wire

-------------
Ted
2nd Year Tier 1 Medical School
Still installing as a hobby...pays for groceries
Compustar Expert

Posted By: coyn11
Date Posted: January 05, 2015 at 1:43 PM

Sweet, thanks guys! Time to dig in!

-------------
NOOB