2010 accord crosstour
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=138210
Printed Date: May 18, 2024 at 10:55 PM
Topic: 2010 accord crosstour
Posted By: ziggyb222
Subject: 2010 accord crosstour
Date Posted: January 10, 2015 at 4:19 PM
Installing a Clifford 4105 in a Honda Crosstour. Using a ADS-ALCA flashed with the DL-HA3 firmare. It programmed correctly but all I get is light flashes and the locks work..but no crank. Everything is soldered and the connection type is hardwired..no data,,,,HELP!!!!!lol
Replies:
Posted By: chev104275
Date Posted: January 10, 2015 at 5:36 PM
Does the car crank at all ? I haven't done a crosstour nor do I do a lot of code alarm but reading the ads ca install guide there's a warning about the gwr coming on before ignition or it will cause immobilizer issues have you tested the gwr ?
-------------
If i Can't Install it I Don't need it Joe
Posted By: Chris Luongo
Date Posted: January 10, 2015 at 7:44 PM
Did you program tach?
Where is the BLACK/ white wire on the Clifford connected?
Posted By: ziggyb222
Date Posted: January 10, 2015 at 7:47 PM
I tried everything..grounded the module before ignition..same thing.. tried leaving the key in the ignition.. I will probably use the firmware just for imobilizer and hard wire the locks and acc ign and starter to the car.. Not in less anyone else has some options????
Posted By: ziggyb222
Date Posted: January 10, 2015 at 8:22 PM
BLACK/ wht is to ground...tach for the clifford to the purle/wht on the ALCA!! Remote start clicks and tries three time...the dash lights never fire up and does not even try to crank
Posted By: tedmond
Date Posted: January 10, 2015 at 8:43 PM
Must have a bad brain. I have done it gen accords without a problem. Meter all rs outputs ?
-------------
Ted
2nd Year Tier 1 Medical School
Still installing as a hobby...pays for groceries
Compustar Expert
Posted By: ziggyb222
Date Posted: January 10, 2015 at 8:53 PM
I had originally tried data...did the same thing...Metered the ignition at the switch...after I hardwired it it was the same...I did not check the output on the start wire connected to the BLACK/ wh on the alca!!!!
Posted By: tedmond
Date Posted: January 10, 2015 at 9:19 PM
Any diagnostics ?
-------------
Ted
2nd Year Tier 1 Medical School
Still installing as a hobby...pays for groceries
Compustar Expert
Posted By: ziggyb222
Date Posted: January 10, 2015 at 9:23 PM
I noticed when attempting to remote start...I get five green light flashes...the as the start continues to try two more time there is not activity on the green light...
Posted By: tedmond
Date Posted: January 10, 2015 at 10:50 PM
i would reprogram the alca. can you do pit stop mode?
-------------
Ted
2nd Year Tier 1 Medical School
Still installing as a hobby...pays for groceries
Compustar Expert
Posted By: ziggyb222
Date Posted: January 11, 2015 at 6:52 AM
I will try today...if not I will hard wire the car and use the firmware for bypass only..Idata is not open for Tech support on weekends I guess..I will swap starter brains and the alca and see if there was a faulty module..and double check my connections on possible cold soldered joint...Other than that I am stumped
Posted By: ziggyb222
Date Posted: January 11, 2015 at 9:34 AM
I am not getting ignition out of the ALCA..run a ignition to the switch on the same wire from the starter direct I get dash lights. but a flashing green key.. does do pit stop fine.. brake signal lock and unlock work fine...
Posted By: tedmond
Date Posted: January 11, 2015 at 12:41 PM
The idatalink doesnt supply an ignition. It only requires an ignition input
You still require power, ground, ign, acc, and start to the key switch. If you have a flashing green key, your bypass isnt turning on before ignition goes on.
-------------
Ted
2nd Year Tier 1 Medical School
Still installing as a hobby...pays for groceries
Compustar Expert
Posted By: ziggyb222
Date Posted: January 11, 2015 at 9:18 PM
I had figured that out and everything works great...only about my tenth Idata module I have used...glad I tried them and Fortin...thanks for the help!!!!!
|