viper 5706v
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=138917
Printed Date: May 15, 2025 at 6:13 AM
Topic: viper 5706v
Posted By: mrainwater6543
Subject: viper 5706v
Date Posted: May 01, 2015 at 7:53 AM
I have a 03 f250 6.0l diesel and trying to install the viper 5706v. I have figured out the wiring for the main 6 pin harness, 3pin door lock harness and the remote start harness. im not sure at all on this 24pin harness.
1...(-)200mA ig 2/flex output...?
2...(-)200mA 2ND STATUS...?
3...(-)200mA TRUNK RELEASE OUTPUT...not used
4...(-)200mA DOME LIGHT OUTPUT...not going to use
5...(-)200mA STATUS OUTPUT...?
6...(-)200mA AUX 3 OUTPUT...not used
7...(-)200mA AUX 1 OUTPUT...not used
8...(-)200mA AUX 4 OUTPUT...not used
9...(-)HOOD PIN INPUT...to engine compartment hood switch
10...(-)TRUNK PIN...not used
11...ACTIVATION INPUT...?
12...TACH INPUT...lt grn/wht wire at pcm
13...(-)NEUTRAL SAFETY...good ground
14...(-)200mA FACTORY ALARM DISARM OUTPUT...not used
15...(-) DOOR INPUT...ye/blk and gray/red wire at vsm
16...(-)200mA HORN OUTPUT...not going to use
17...(-)200mA IGNITION 1 OUTPUT...?
18...(+) DOOR INPUT...not used
19...(-)200mA AUX 2 OUTPUT...not used
20...BRAKE SHUTDOWN INPUT...rd/lt grn at brake pos. switch
21...(-)200mA STARTER OUTPUT...?
22...(-)DIESEL WAIT TO START...dont think i need, set start on timer?
23...(-)200mA ACC OUTPUT...not used
24...(-)200Ma FACTORY ALARM ARM OUTPUT...not used
anyway does that look right and do i need diodes on the door input wires? will make a good write up when im done so the question wont have to be asked again, thanks for the help
Replies:
Posted By: howie ll
Date Posted: May 01, 2015 at 8:26 AM
The status outputs aren't needed unless there's a by-pass involved.
Neither are 11, 17 and 21.
1N4004 diodes, bands to VSM
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: mrainwater6543
Date Posted: May 01, 2015 at 8:35 AM
awesome! thank you, the unlock and lock outputs in the door lock harness do they need diodes as well?
Posted By: howie ll
Date Posted: May 01, 2015 at 8:38 AM
The status outputs aren't needed unless there's a by-pass involved.
Neither are 11, 17 and 21.
1N4004 diodes, bands to VSM.
Door trigger at H2/15 needs to be programmed for N/C, menu 1, feature 13 option 2.
Hood trigger at H2/9 ditto, menu 1 feature 11, option 2.
There are 3 ACC wires at the ignition.
Join orange at H3 to one, pink/white at H3 to second, program- menu 3, feature 8, option 2 and take the orange at H2/23 to relay, terminal 85.
86 and 87 to 15 amp fused constant 30 to ACC 3, diode between 86 and 85, 1N4004, band to 85.
One of your status wires goes to the key sense.
PM me with your email address for full installation instructions.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: mrainwater6543
Date Posted: May 01, 2015 at 8:46 AM
Im also not using a bypass the truck doesnt have immobiliser
Posted By: howie ll
Date Posted: May 01, 2015 at 10:04 AM
OK fine one of the status wires for key sense, no diodes on the locks.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: mrainwater6543
Date Posted: May 01, 2015 at 11:12 AM
for the key sense wire can i hook it up to H2/2 (-)200mA 2nd status?
Posted By: howie ll
Date Posted: May 01, 2015 at 12:10 PM
Yes, either status wire.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
|