Viper 4105v and Smart start
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=139188
Printed Date: May 17, 2025 at 7:49 AM
Topic: Viper 4105v and Smart start
Posted By: kw4tx
Subject: Viper 4105v and Smart start
Date Posted: July 12, 2015 at 1:04 PM
I have a 4105v and a smart start.... I have installed a smart start in the past but am confusing myself ...probably again...
Question:
Viper shows and ESP port and a D2D port...(red) beside light jumpers
Smart Star has 3 plugs...black...brown and white...
I cant figure out whether the brown wire or white goes to D2D or the Black goes to ESP
I dont think I have to use both ESP and D2D...
So my question is Brown to D2D or white...?
And do I use Black ESP ?
Am I making myself clear?
Replies:
Posted By: kw4tx
Date Posted: July 12, 2015 at 1:19 PM
I also noticed my smart start doesn't have loops as stated ....It has a short grey wire and a short white wire...
are these supposed to be loops and cut if using RSR?
I have no bypass kit...
installing in a 2006 Crown Victoria P71
Posted By: howie ll
Date Posted: July 13, 2015 at 2:45 AM
Use the black plug on the Viper, red and black SmartStart to same colours on Viper H1, ignore the short grey and white wires.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: kw4tx
Date Posted: July 13, 2015 at 3:49 AM
SO I don't use the Red plug or the white?
I use the black on ESP port... and not the red or white...
Posted By: howie ll
Date Posted: July 13, 2015 at 4:24 AM
Yes.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: kw4tx
Date Posted: July 13, 2015 at 4:29 AM
Thanks Howie....
Posted By: kreg357
Date Posted: July 13, 2015 at 5:34 AM
Additional help...
Red 4 pin port, Bitwriter/ESP2 or D2D programming
The Red 4-pin plug may be configured as a Bitwriter/ESP2 or D2D port.
The factory default is Bitwriter/ESP2 mode.
To use as D2D mode follow the below steps:
1. Make sure WHITE/ Blue activation wire is grounded.
2. Power the unit up. The system LED flashes for 5 seconds to confirm D2D mode change.
3. Remove the WHITE/ Blue wire from ground.
To change from D2D to Bitwriter/ESP2 mode:
1. Make sure the WHITE/ Blue activation w ire is grounded.
2. Power the unit up, the system LED turns on solid for 5 seconds to confirm Bitwriter ESP2 mode change.
3. Remove the WHITE/ Blue wire from ground.
The procedure con be repeated to toggle from one mode to the other. ------------- Soldering is fun!
Posted By: howie ll
Date Posted: July 13, 2015 at 11:04 AM
Once AGAIN use RED and BLACK joined to the SAME colours on H1 don't use grey or white.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: iceman1234
Date Posted: January 20, 2018 at 12:05 AM
howie ll wrote:
Once AGAIN use RED and BLACK joined to the SAME colours on H1 don't use grey or white.
Hey Howie,
I have the same problem as him.
I have the 4x03 module and I am also trying to connect Dsm350 to the module. I have solid amber light and green light on the DSM350 but the problem is I can’t smart start the car on my phone. Only lock and unlock work. There are 4 pin white, 4 pin brown, 3 pin black plugs from DSM350
I used the white and black plug and plug them into 4x03 module on the black and red port.
Any suggestions are appreciated.
Thank you.
|