2005 Honda Odyssey, Door Trigger?
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=141035
Printed Date: April 25, 2024 at 6:36 PM
Topic: 2005 Honda Odyssey, Door Trigger?
Posted By: kulblue
Subject: 2005 Honda Odyssey, Door Trigger?
Date Posted: March 19, 2016 at 12:47 AM
Hi,
The alarm system -neg door trigger can connect to dome light? Instead doing individual door trigger? For Honda Odyssey 2005. Thanks
Replies:
Posted By: syl20rochon
Date Posted: March 19, 2016 at 6:39 AM
Are you doing an alarm only or alarm/remote starter? It is best to connect door pin trigger input to door pins at all times. On your Honda, you'll have to use 4 wires (FL, FR, RL, RR) isolating with diodes. If you're doing an alarm only, you can use the domelight connection but it can result in false alarm triggers.
Diodes------------- Sylvain Rochon
MECP security specialist
Tech support for remote starters
26 Years of experience counts
I'm here to help.
Posted By: kulblue
Date Posted: March 19, 2016 at 2:10 PM
I'm doing remote start and alarm... I have hard time to find all trigger on the fuse box.
Posted By: syl20rochon
Date Posted: March 19, 2016 at 2:15 PM
Notes
The individual door trigger wires are at the rear of the driver fuse/relay box in the driver kick. The LF door is green in a 16 pin plug, pin 15. The RF door is lt. GREEN/ red in a 14 pin plug, pin 12. The LR door is GREEN/ YELLOW in a 16 pin plug, pin 14. The RR door is GREEN / WHITE in a 14 pin plug, pin 13. Use all four wires and diode isolate each.
-------------
Sylvain Rochon
MECP security specialist
Tech support for remote starters
26 Years of experience counts
I'm here to help.
Posted By: syl20rochon
Date Posted: March 19, 2016 at 2:20 PM
I don't know what bypass module you're using but you can use the DBALL2 from Directed, you won't have to wire door pins since they'll be supplied by the CAN bus network thru the module.
-------------
Sylvain Rochon
MECP security specialist
Tech support for remote starters
26 Years of experience counts
I'm here to help.
Posted By: syl20rochon
Date Posted: March 19, 2016 at 2:25 PM
Detailed Function List
W2W
DL-Arm Factory Security
DL-Disarm Factory Security
DL-Door Lock Control
DL-Door Unlock
DL-Driver Priority Unlock
DL-Sliding Door Control Driver
DL-Sliding Door Control Passenger
DL-Trunk / Hatch Release
PK-Immobilizer Bypass-Data No Key Req'd
RS-Tach / RPM Output
SS-Entry Monitoring ALL Door Pins
SS-Entry Monitoring Hood Pin
SS-Entry Monitoring Trunk/Hatch Pin
ST-Brake Status (foot brake)
ST-E-Brake Status
D2D
DL-Arm Factory Security
DL-Disarm Factory Security
DL-Door Lock Control
DL-Door Unlock
DL-Driver Priority Unlock
DL-Sliding Door Control Driver
DL-Sliding Door Control Passenger
DL-Trunk / Hatch Release
FOB-Control of aftermarket alarm with OEM remote
PK-Immobilizer Bypass-Data No Key Req'd
RS-Tach / RPM Output
SS-Entry Monitoring ALL Door Pins
SS-Entry Monitoring Driver Door Pin
SS-Entry Monitoring Hood Pin
SS-Entry Monitoring Trunk/Hatch Pin
ST-Brake Status (foot brake)
ST-E-Brake Status
-------------
Sylvain Rochon
MECP security specialist
Tech support for remote starters
26 Years of experience counts
I'm here to help.
Posted By: kulblue
Date Posted: March 20, 2016 at 12:35 AM
Thanks for help and info. I tried to find all doors trigger on fuse Box but no luck. I check the black loom in the driver side panel, I found all doors trigger  . Now I need to find and run extra wire for the trunk/hatch pin trigger.
I had the dball and avital installed and now I installed Cardot alarm remote start, push to start and pke. I used DEI universal interface bypass.
|