2016 Wrangler Avital 5305L Error after Install

Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=141812
Printed Date: April 27, 2024 at 11:09 PM

Topic: 2016 Wrangler Avital 5305L Error after Install

Posted By: silverhobo
Subject: 2016 Wrangler Avital 5305L Error after Install
Date Posted: October 02, 2016 at 10:03 PM

I have a 2016 Jeep Wrangler Unlimited with no power doors or windows. I started by installing power actuators in all the doors and connected them to the avital 2101L door remote system.

I have since decided to upgrade to remote start.

I them got an avital 5305L kit, I also purchased the DBALL2 (Flashed with the xkloader2 for my vehicle) and the CHTHD2 wiring harness.

I followed the instructions on this site to do the installation (Using D2D and Remote Start Ready Instructions) and my Jeep remote starts just fine.

I discovered during the install that I had to wire the door locks through relays and they also work.

Remote Start Ready Instructions - See Page 9

My problem is that the LED on the Control Center / Antenna blinks 3 times then pauses 2 seconds then starts the cycle again. (Door Switch Trigger)

I have the (-) DOOR TRIGGER INPUT hooked up to both the dball2 and the 5305L per the instructions.

I hooked the BLACK/ white hood pin wire from the dball2 to the same ground that the 5305L is using.

NOTE: Jeep started with and without the above 2 wires being hooked up.

On the 5-Pin connector the following wires ARE hooked up:

01 - BLACK    (-) CHASSIS GROUND
03 - RED      (+) FUSED 12V DC CONSTANT INPUT
05 - WHITE    (+)/(-) SELECTABLE PARKING LIGHT OUTPUT (FUSED)

On the 24-Pin connector the following wires ARE hooked up:

04 - BLACK / YELLOW (-) 200mA DOME LIGHT OUTPUT
13 - BLACK/ WHITE (-) PARKING BRAKE INPUT/EMERGENCY INPUT -
       Wired to ground with switch
15 - GREEN        (-) DOOR INPUT

I want to make some changes to the programming but can't until I get this problem taken care of.

Thanks for your help

Erv

-------------
SilverHobo

Replies:

Posted By: Ravendarat
Date Posted: October 04, 2016 at 8:57 PM

Disconnect the black white wire from the Dball2 and see if that helps, that wire off the tharness shouldn't be grounded, thats a wire to use for the hood pin

-------------
double-secret reverse-osmosis speaker-cone-induced high-level interference distortion, Its a killer

Posted By: silverhobo
Date Posted: October 04, 2016 at 10:30 PM

Ravendarat wrote:

Disconnect the black white wire from the Dball2 and see if that helps, that wire off the tharness shouldn't be grounded, thats a wire to use for the hood pin

Ravendarat, Thanks for the Help!

OK, I unhooked the black / white wire from the dball to ground.

UPDATE: I had posted that I had wired the both of the (-) door trigger wires to my (-) door trigger, I realized late last night that I hadn't that and did so.

I hooked up the Shock Sensor to the 5305, after testing, I turned the adjustment all the way down.

I also hooked up the siren.

There has been no change in the LED on the Control Center / Antenna.

Is there a way to reset the 5305?

If so I will take the module out, reset it and start over.

-------------
SilverHobo