Print Page | Close Window

2016 Nissan Rogue

Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=141872
Printed Date: November 29, 2021 at 8:28 AM


Topic: 2016 Nissan Rogue

Posted By: daflipcyde
Subject: 2016 Nissan Rogue
Date Posted: October 16, 2016 at 10:01 PM

Rogue with intelli key. After installing remote start system and testing without plugging in all the harnesses on the front dash like eco, awd, tc, etc. I get all the errors even after having them plugged in. I don't have obd scan tool. I unhooked battery for 10 minutes still having the problem. Any way to get rid of theerrors?



Replies:

Posted By: geepherder
Date Posted: October 17, 2016 at 10:58 AM
10 minutes might not be long enough. I can't guarantee this will work either, but it's worth a try. With the negative battery terminal disconnected, touch the negative battery cable to the positive battery terminal for a couple of seconds. Then reconnect the battery.

-------------
My ex once told me I have a perfect face for radio.




Posted By: Mark Mizenko
Date Posted: October 18, 2016 at 8:26 PM
I do a couple of 16 rogues every week, I-Key and flip key, and always test them without those mentioned switches plugged in, I never had that happen. I would recheck all your connections. Did you do 3XL? That only requires connections at 3 plugs at the BCM, very simple. I would check the plugs/pins.

Was one of your 3 neg. ignitions an aluminum wire. How did you connect to that if it was. I assume you used diodes on these also.




Posted By: daflipcyde
Date Posted: October 19, 2016 at 4:11 PM
I used al ca and yes I used diodes on the on the ignition wires. I checked all connections and looks good. Can't figure it out. No I did regular install not 3XL.




Posted By: daflipcyde
Date Posted: October 19, 2016 at 8:24 PM
I don't one of the ignition wire was aluminum. Should it have been?




Posted By: beegbie
Date Posted: October 20, 2016 at 1:41 AM
Yes, as long as it's made by Nissan and not Renault Samsung (RSM). Did the bcm slide out after removing one 10 mil? If yes, the violet wire should have been aluminum.




Posted By: Mark Mizenko
Date Posted: October 20, 2016 at 9:55 PM
I find them aluminum and copper. I just asked you to check.

You flashed the alca correctly? It programmed / cloned without any problems?






Posted By: daflipcyde
Date Posted: October 21, 2016 at 10:27 AM
posted_image

I tapped into the brown, yellow, and white. White was aluminum I soldered the WHITE/ black from al ca and diode isolated all 3 including the aluminum wire. The al ca programmed / cloned properly with no problems.

Yes the bcm just had 1 10 mil and slide out easily.




Posted By: daflipcyde
Date Posted: October 21, 2016 at 2:34 PM
Here's the update. The only time I get the AWD warning and i-key warning is upon takeover.

Idata states to takeover simply get in close the door, press and release brake. When I do that nothing happens. Can't get into gear. So while engine is still running and I press brake and start I get the error. I also tried just pressing start after the takeover procedure same problem. Am I doing something wrong?

I also tried W2W on the brake.

Also nothing happens after 45 seconds when doors are unlocked and leaving door open.




Posted By: beegbie
Date Posted: October 21, 2016 at 4:55 PM
Have you tested the pts wire? The only function of this connection is for automated takeover. ORANGE / black should go to to a yellow wire that tests as ground only when the pts button is pressed.




Posted By: daflipcyde
Date Posted: October 21, 2016 at 7:52 PM
I don't have the vehicle in my possession right now so I won't be able to test. So the only function of the orange / black is for takeover? It's not used as well to start the vehicle under remote start?




Posted By: beegbie
Date Posted: October 22, 2016 at 8:15 PM
daflipcyde wrote:

I don't have the vehicle in my possession right now so I won't be able to test. So the only function of the orange / black is for takeover? It's not used as well to start the vehicle under remote start?


Correct. The blue / YELLOW starts the car. ORANGE / black is for takeover.





Print Page | Close Window