1998 K1500 bypass

Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=141922
Printed Date: May 06, 2024 at 11:54 PM

Topic: 1998 K1500 bypass

Posted By: tintmaster2001
Subject: 1998 K1500 bypass
Date Posted: October 28, 2016 at 2:17 AM

Please help! Doing my second remote start on my 1998 Silverado and I have never installed a bypass, I just received a passlock SL2 and was hoping someone can show me a wiring diagram.
THANKS for any info.

Replies:

Posted By: geepherder
Date Posted: October 28, 2016 at 9:02 AM

Here's a good place for reference: https://12voltinstallations.8m.com/photo.html

-------------
My ex once told me I have a perfect face for radio.

Posted By: tintmaster2001
Date Posted: October 28, 2016 at 9:53 AM

Thanks!

Posted By: tintmaster2001
Date Posted: October 31, 2016 at 5:24 PM

Hey guys still need some help. Where do I hook up the blue negative wire that goes to the remote start it just says "while running" THANKS!

Posted By: geepherder
Date Posted: October 31, 2016 at 8:41 PM

If you're using a relay like in the link, it goes to terminal 85. If you have a bypass interface, it should come with a diagram and show you where it goes.

-------------
My ex once told me I have a perfect face for radio.

Posted By: tintmaster2001
Date Posted: October 31, 2016 at 9:20 PM

Is it necessary to use a relay? I'm trying to follow these instructions on this website https://fortin.ca/download/24951/passlock-sl2v2_revi.pdf
i just can't figure out where the blue wire goes on the remote start. I'm following number 4 diagram. thanks for your response geepherder.

Posted By: rmotlyintrested
Date Posted: October 31, 2016 at 9:56 PM

I'm not an expert but I think you'll find that it doesn't exactly say "while running", it says, "(-) while running". In other words, ground while running or "ground out" while running. There should be an output by that name on your remote start or it may also be called "status output". Hope this helps.

Posted By: tintmaster2001
Date Posted: October 31, 2016 at 10:02 PM

Thanks will try it tomorrow.

Posted By: tintmaster2001
Date Posted: November 01, 2016 at 8:05 PM

Still no luck, it starts for a second and dies. I programmed the bypass and hooked up the(-) blue wire "while running" wire to status output and nothing. posted_image

Posted By: geepherder
Date Posted: November 01, 2016 at 11:40 PM

The problem may have nothing to do with your Passlock bypass, so tell us what system you're installing.

-------------
My ex once told me I have a perfect face for radio.

Posted By: tintmaster2001
Date Posted: November 03, 2016 at 3:48 PM

I finally got it! I was using the wrong ignition wire. I needed to tap on a small yellow wire right at the ignition switch not the ignition wire under the dash. Now I have to figure out the relays for my door locks, My fist remote start was on a 95 f-150 so it was really easy. This bypass was a new one for me. I been a tinter for 13 years and really want to start doing alarms and remote start for the slow winter months, thanks everyone for your help posted_image