viper 5706V, 2008 Hyundai Elantra
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=142172
Printed Date: April 27, 2024 at 8:44 AM
Topic: viper 5706V, 2008 Hyundai Elantra
Posted By: mmatrisch
Subject: viper 5706V, 2008 Hyundai Elantra
Date Posted: December 04, 2016 at 11:15 PM
trying to install a viper-5706v on wifes car all works however i need to wire the oem arm and disarm wire's from the viper system into the car and im at a loss on how to do this she has a 2008 Hyundai elantra directed electronics directwire instructions say to refer to tech doc 1300 i can not find it anywhere please help ASAP
-------------
Matt
Replies:
Posted By: i am an idiot
Date Posted: December 05, 2016 at 8:47 AM
Factory Alarm Arm GREEN (-) IN HARENSS IN DRIVER KICKPANEL TO DOOR TO TEST THIS WIRE USE THE DRIVER KEY CYLINDER TO LOCK THE DOOR
Factory Alarm Disarm BLUE (-) IN HARNESS IN DRIVER KICKPANEL TO DOOR MAY ALSO BE YELLOW, TO TEST THIS WIRE USE THE DRIVER KEY CYLINDER TO UNLOCK THE DOOR
Posted By: mmatrisch
Date Posted: December 05, 2016 at 9:12 AM
Is there any diode configuration that needs to be setup between the factory alarm and the viper alarm or just plug them in straight
-------------
Matt
Posted By: mmatrisch
Date Posted: December 05, 2016 at 9:45 AM
OK after testing the yellow wire I use the key the first time I turn it it does nothing I turn it again the tone drops for a brief second is that the wire I'm looking for
-------------
Matt
Posted By: i am an idiot
Date Posted: December 05, 2016 at 10:19 AM
It pulsing the second time you turn key tells me that it is the door unlock wire for the 3 doors other than the drivers door. Does the Blue wire pulse at the first turn of the key? A lot of times the door lock and unlock wires turn factory alarm on and off. It looks like this is the case for your car.
Posted By: mmatrisch
Date Posted: December 05, 2016 at 11:04 AM
no the wire that pulsed the first time you turn the key was the YELLOW /GREEN wire in the grey 39pin harness YELLOW /GREEN= driver door pulse blue wire= pax door and the two back doors
i have another question for you trying to wire up the trunk release found the wire in the harness found the wire on the viper system however when i attempt to activate the trunk release wire it does nothing i tried to tone it and i get no response at all do i need to dig out my bit-writer and activate this wire
-------------
Matt
Posted By: mmatrisch
Date Posted: December 05, 2016 at 11:10 AM
one more question the directed directwire print out im using says that the door triggers are as followed red wire=driver yellow wire does the rest however the yellow wire is dome light supervision and that stays on for a few sec after door is closed how would i work around that
-------------
Matt
Posted By: mmatrisch
Date Posted: December 05, 2016 at 4:24 PM
Wanting to wire priority unlocking into my wife's car she has a viper-5706v and a 2008 Hyundai Elantra s.e. I have the whole car unlocking on one push of the unlock button but I don't know the wire color(s) to accomplish this
-------------
Matt
Posted By: mmatrisch
Date Posted: December 06, 2016 at 2:21 AM
2008 Hyundai Elantra. Does anyone know the way to wire up a viper 5706v to unlock the driver door first with one push of the button and unlock the other doors with another push of the unlock button I need the wire color for the car if anyone has an idea
-------------
Matt
Posted By: i am an idiot
Date Posted: December 07, 2016 at 10:23 AM
Have you tried using YELLOW /GREEN as unlock wire to see if that just unlocks drivers door? If so what happens if you press the remote a second time?
|