Viper 4706V w/dball2 in Mazda 2 2011

unable to program dball2 not sure if i'm missing anything.
this list has the ones i connected.
DBALL2:
Red harness:
H9: violet/brown (door lock output mux)--powerlock pink in mazda2
H10: yellow/black ( Data Tx)            -- green in mazda2
H11: ORANGE / black (Data Rx)             -- grey in mazda2

Blue Harness:
H3: tan/black: HS CAN High pin6
H4: tan      : HS CAN Low pin14

Black harness:
H9: + ignition input

D2D to viper

ON the VIPER 4706v:
Heavy gauge relay wire 8 pin harness:
#1 RED / blck to 12(+) --red
#2 pink/blck        --not used
#3 pink/white to ACC2--bla=\ck/white
#4 red to 12(+)      --red
#5 violet to starter --BLACK/ blue
#6 orange to ACC1    --BLACK/ red
#7 RED / white to 12(+)--red
#8 pink to ignition --BLACK / YELLOW

Main Harness 6 pin connector:(this is where i know i need help)
H/1 red 12(+)--red in mazda2
H/2 Black ground(-)
H/3 not used
H/4 not used
H/5 to parking lights(-) BROWN / white w/fuse set to (-) on viper
H/6 not used

Door lock 3 pin connector not used

Auxiliary/shutdown Harness 24 pin:(also unsure)
i only connected
H/13 BLACK/ white to ground(-)


thanks

Do you get the solid red light?

-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation

yes i do.
i put the first key and then it flashes green,
then within 3 secs i put the 2nd key and it flashes orange.
then i remove the key and within 3 secs i'm supposed to remote start the car whie holding the program button on the dball2.
but my 2 way remote shows me fails to communicate with viper.
and the car never remote start to finish the programming.

i disconnected the dball2 wiring to get the red light.
and tried all over about 4 times still no luck.
thanks

Sounds like the remote needs to be paired to the brain.
I would go through the pairing procedure.

-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation

the pairing procedure talks about a control center button. i don't what that is.

That would be the button on the antenna, called the control center.

-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation

thanks to you. i'm making progress.
i was able to pair it now.
and the remote responds with lock and unlock functions with parking lights flashing but doors don't lock or unlock.
but now i get error code instead on the last step of programming the dball2. first and second step is good but the third step while i'm supposed to hold the dball2 button and press remote start that's where it fails it displays an error on lcd remote.

Just above step 2 on page 7, it states to make sure all door are closed before executing the programing sequence.

Are all door closed?

-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation

yes i tried with all doors closed.with no luck.
also in order to get the solid red light back i diconnect all wiring from dball2 and plug the black then red then blue connector and press and hold the dball2 button and plug the white D2D and release button.

when i bought the dball2. according the ebay seller he said he flashed it for mazda2.

also is the programming necessary to unlock and lock doors, since now i only see the lights flashing on mazda2 but locks don't respond.

on that 3rd step the the car lights flashes about 7 times.
saw somewhere online that it's possible that viper is on manual mode

If your Mazda is automatic transmission then the Viper needs to be put into automatic mode.
Menu 3, Item 1, Option 2, using the control center button and the remote.

Ignition on then off. press and hold the button until the horn chirps three times, or LED blinks three times, then release. press and release button 1 time, then press and hold. using the remote press the lock button.
That should put it into auto mode, release the button. wait 30 seconds for the system to exit the programming. Then try to program the DBALL.



-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation

niiiiiiiice
thanks a million
you the best i'm all set. remote start and lock and unlock work as a charm. once i switched to automatic trans mode.

one more thing :))

i wanted to hook up the window since my mazda has driver roll/up/down window. on page 3 both lines shows in red. on the black pin they are h#4, h#5. i need to know where do i tie them up to the viper.

thanks again.

Never done that but looks to me to be
24 Pin harness, Pin 7, WHITE/ Violet is AUX 1, and Pin 19, Violet/Black is AUX 2.

-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation

the window roll/down didn't work after i tied the wires you mentioned. instead aux triggers to unlock doors.
windows thing is not a big deal at all to me.
I'm all good with the main option of remote start.

thanks again and nice chatting with you smokeman......
Peace...

I'm looking to extend engine running time from 12 min on my viper4706v???
thanks.

Same procedure as changing from manual to automatic, EXCEPT, it is Menu 3, Item 4, Option 2.


-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation

nice.

thanks again

https://www.the12volt.com/installbay/downloads.asp?srch=all&term=viper+quick

Quick Reference guide.

-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation

Did you end up connecting anything else to the Aux harness or the viper?, im in the process of doing a 2011 mazda 2 but it is manual. Ill be posting a thread which includes the install process of my 4806 and ALCA.

no