viper 4806v into 2001 jeep gc
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=142811
Printed Date: May 01, 2024 at 10:44 PM
Topic: viper 4806v into 2001 jeep gc
Posted By: jwmsguu912
Subject: viper 4806v into 2001 jeep gc
Date Posted: March 29, 2017 at 1:45 AM
Hello everyone need help I'm installing a viper4806v into jeepgc 2001 and all I get is seven clicks out of viper unit anyone willing to help
my understanding is red red red/blk red/wht connected to red 12v in keep
H3/8 pink to dark blue in ign switch h3/5 violet to yellow ign switch h3/6 orange to red/blk acc.1 ign switch h3/3 pink/wht to acc.2 orange/blk ignswitch h3/2 pink/blk nu all blk wires ground to chassis then I have h2/12 violet/wht to cool h2/9 gray to hood pin h2/20 brown to brake switch h2/13 blk/wht to chassis and a 455j interface module hooked up to light driver kick panel or under dash light also this ford transponder keybypass wired in as well so all I get is seven clicks from viper is this a programming issue or did I forget something? Anything from anyone would be more than where I got thank you guys very much
Replies:
Posted By: smokeman1
Date Posted: March 29, 2017 at 8:54 PM
Is the Jeep a Auto Transmission? Sounds like the Viper unit is in manual transmission mode.
Should have started a new separate topic for your install.
-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation
Posted By: jwmsguu912
Date Posted: March 30, 2017 at 3:17 PM
Jeep is automatic and this was the only place it would let me post and on another note I can't seem to get into programming
Posted By: silvercivicsir
Date Posted: March 30, 2017 at 4:38 PM
did you ground the thin blk/white netural safety wire? and did you hook up light flash? pretty hard to program without the light flash hooked up.
Posted By: jwmsguu912
Date Posted: March 30, 2017 at 4:47 PM
Yes neutral safety is grounded but this light flash which wire is it it? thank you so much for postin back
Posted By: silvercivicsir
Date Posted: March 31, 2017 at 8:48 AM
sorry it's a viper, light flash doesn't do that much vs compustar, but it still should be hooked up. What happens when you try to get into programming mode?
Posted By: jwmsguu912
Date Posted: March 31, 2017 at 3:21 PM
Well I'm trying to go into programming I turn on then off press an hold, there's no honk and the led steadily flashes
Posted By: silvercivicsir
Date Posted: March 31, 2017 at 4:39 PM
were you able to program Tach? if you didn't hook the horn wire (gray/orange @ horn switch), it won't honk.. Just to be sure, you are turning the Jeep to "on"? two clicks, not the first "accessory"?
Posted By: jwmsguu912
Date Posted: March 31, 2017 at 5:06 PM
yes horn is hooked up to gray/orange and I do turn two clicks and am at the jeep now trying again
Posted By: jwmsguu912
Date Posted: March 31, 2017 at 5:30 PM
I'm so... you know I guess the door had to be open to get into programming I got it into automatic I set flex relay to acc.2, but now the car only starts and dies after a second something I'm forgetting I think again thanks to everyone for the posts 12volt rock daps to all
Posted By: jwmsguu912
Date Posted: March 31, 2017 at 6:06 PM
Ok one more thing i can't seem to lock or unlock with remote I was able to before why not now? any insight on this very much appreciated oh btw I set to tachometer and r/s works great just the lock/unlock is gettin me again thanx so much
Posted By: jwmsguu912
Date Posted: April 01, 2017 at 4:57 AM
Ok I was thinking should I go ahead an connect wires from the door for lock/unlock it's just I didn't have to before this time the car honks when I press lock or unlock and it doesn't even lock or unlock I mean it did before the r/s problems and now it's this any help please
|