2006 Ram 3500 Diesel, Compustar 4900s Remote Start Issue
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=146101
Printed Date: April 24, 2024 at 5:00 AM
Topic: 2006 Ram 3500 Diesel, Compustar 4900s Remote Start Issue
Posted By: mrcommando
Subject: 2006 Ram 3500 Diesel, Compustar 4900s Remote Start Issue
Date Posted: March 23, 2020 at 7:52 PM
I have a Compustar 4900s with Blade-AL bypass and I’m running into a very dumb issue. The truck remote starts and shuts off after about 5 seconds and then says it’s running. I’ve tried reprogramming the tach sensing. I tapped into the tach wire but idk why it won’t sense that the engine is on. I’m stumped. Help please!
-------------
2006 ram 3500
Replies:
Posted By: mrcommando
Date Posted: March 23, 2020 at 7:52 PM
It has the standard turn key with keyless entry.
-------------
2006 ram 3500
Posted By: chev104275
Date Posted: March 24, 2020 at 5:01 AM
Ive never done one of those trucks but maybe try a different tach signal. On DIESEL'S the Tach wire is at the ECM, on the lower drivers side of the engine, FRONT 60-Pin plug, Pin 24 or at the Camshaft Position Sensor just LEFT of the ECM in a 3-Pin plug. (AC)
-------------
If i Can't Install it I Don't need it Joe
Posted By: mrcommando
Date Posted: March 24, 2020 at 11:55 AM
I tried pin 24 and nothing. Tested and volts didn’t go up with rpm. I’ll try the camshaft position sensor wire
-------------
2006 ram 3500
Posted By: chev104275
Date Posted: March 24, 2020 at 5:25 PM
How are you testing the wire ?
-------------
If i Can't Install it I Don't need it Joe
Posted By: mrcommando
Date Posted: March 24, 2020 at 7:57 PM
Any remote starter installers out there?? Trying to install a compustar cs4900 with blade al immobilizer bypass module on a 2006 ram 3500 cummins and it remote starts up fine but shuts off after 3 seconds. It only remote starts and stays running when there is a key in the ignition cylinder. Help me out here! It is wired correctly that’s for sure. Tach is programmed too
-------------
2006 ram 3500
Posted By: mrcommando
Date Posted: March 24, 2020 at 8:50 PM
Hey man I got the tach signal down but now it only stays running when there is a key in the ignition. With no key in ignition it starts and shuts off after 3 seconds. I’m thinking it’s the immobilizer
-------------
2006 ram 3500
Posted By: wirewise
Date Posted: March 24, 2020 at 9:02 PM
Sounds like you do not have the ignition wire(s) properly connected to keep it running.
-------------
~wirewise~
Verify all wiring with your meter before making any connections!
Posted By: chev104275
Date Posted: March 25, 2020 at 6:16 AM
How is everything wired ? Is the diode in place and the correct orientation ? Did the blade program correctly ? If you start the truck with the key can you do a pit stop and remove the key but have the truck continue to run ? If the truck starts and runs with the key in the ignition I would look into the bypass side of things.
-------------
If i Can't Install it I Don't need it Joe
|