Recognize This Alarm?
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=147243
Printed Date: July 04, 2025 at 1:29 PM
Topic: Recognize This Alarm?
Posted By: rocko9999!
Subject: Recognize This Alarm?
Date Posted: February 03, 2022 at 3:44 PM
Replies:
Posted By: rocko9999!
Date Posted: February 03, 2022 at 3:45 PM
Valet switch?
Posted By: i am an idiot
Date Posted: February 03, 2022 at 8:15 PM
It is not doing anything with the transmission. It has a starter disable. Year Make and Model of the vehicle it is in?
-------------
Let's Go Brandon Brown. Congratulations on your first Xfinity Series Win. LGBFJB
Posted By: rocko9999!
Date Posted: February 04, 2022 at 12:13 PM
2021 Toyota Rav4. Only reason I assumed it was connected to transmission switch was the message to 'shift into Park to start' when the module was unplugged.
Posted By: rocko9999!
Date Posted: February 04, 2022 at 12:16 PM
Taps
One of the wires it's spliced in to.
Posted By: rocko9999!
Date Posted: February 04, 2022 at 12:17 PM
Yellow wire it's spliced in to.
Posted By: i am an idiot
Date Posted: February 04, 2022 at 7:28 PM
Reconnect the 2 ends of the yellow wire. This should allow the vehicle to start with the module unplugged. If you are removing the module from the vehicle, I suggest you remove 1 t tap at a time and make sure the car starts and runs properly after each disconnect.
-------------
Let's Go Brandon Brown. Congratulations on your first Xfinity Series Win. LGBFJB
Posted By: i am an idiot
Date Posted: February 04, 2022 at 10:06 PM
The reason it says to shift into park to start is because the only thing between the push to start button and the starter solenoid is the neutral safety switch. The cars computer knows the start button was pressed, and the signal did not reach the solenoid, so it thinks the neutral safety switch is what stopped the signal. The car was not expecting the starter interrupt box being on the vehicle.
-------------
Let's Go Brandon Brown. Congratulations on your first Xfinity Series Win. LGBFJB
Posted By: rocko9999!
Date Posted: February 07, 2022 at 1:33 PM
i am an idiot wrote:
Reconnect the 2 ends of the yellow wire. This should allow the vehicle to start with the module unplugged. If you are removing the module from the vehicle, I suggest you remove 1 t tap at a time and make sure the car starts and runs properly after each disconnect.
Thanks I will try this.
Posted By: rocko9999!
Date Posted: February 07, 2022 at 1:35 PM
i am an idiot wrote:
The reason it says to shift into park to start is because the only thing between the push to start button and the starter solenoid is the neutral safety switch. The cars computer knows the start button was pressed, and the signal did not reach the solenoid, so it thinks the neutral safety switch is what stopped the signal. The car was not expecting the starter interrupt box being on the vehicle.
Ah, makes sense. Thank you. Was the dash mounted switch for valet or to disable the alarm?
Posted By: i am an idiot
Date Posted: February 07, 2022 at 2:59 PM
I have no idea.
-------------
Let's Go Brandon Brown. Congratulations on your first Xfinity Series Win. LGBFJB
|
