2011 Lexus RX350 PTS, DB3
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=147557
Printed Date: April 26, 2024 at 4:08 AM
Topic: 2011 Lexus RX350 PTS, DB3
Posted By: wyciwug
Subject: 2011 Lexus RX350 PTS, DB3
Date Posted: January 07, 2023 at 7:33 PM
I bought and installed this system DB3 WITH T HARNESS, connected only 4 wires. programmed the module, seem to be ok but car not started.
I pressed thr keyfob lockx3, during the remote start, i saw the LED light on the module flash green slow, then red/orange a few times, then flash green fast. THEN nothing happened. AND the LED light repoeated 2 more time, nothing happened after that. I WONDER WHAT did I do wrong. PLEASE HELP. THANKS
I did soft reset three times and reprogrammed the module 3times.
I only used connecrors 14 and 12 with total of 5 wires used total.
THarness from plug #14
1/ YELLOW WIRE from the Tharness to pin #4 lt green
PLUG #12:
1/ GREEN/Black to PTS switch PIN
#7 lt green
2/ Red/black to violet pin#30 @ BCM black 30-pin plug
3/ yellow/black to pink #4 pin @bcm 30-pin pluh
4/ Orange/black to lt green pin# 16 @bcm 30-pin plug
Did not use #10 because it did not come with the switch and hood switch.
The item is below.
Remote Start Compatible with Lexus 2010-2015 RX 350"Push-to-Start Models ONLY Includes Factory T-Harness. Professional Installation Recommended https://a.co/d/5mH0pRJ
-------------
DCD
Replies:
Posted By: silvercivicsir
Date Posted: January 07, 2023 at 9:02 PM
did you try and start it with the door closed?
Posted By: wyciwug
Date Posted: January 07, 2023 at 9:29 PM
Hello
YES it was closed the whole time and I even check brake and hand Brake too, the hood. SHOuld I ground the white/black to car chassis from 10-pin?
-------------
DCD
Posted By: silvercivicsir
Date Posted: January 07, 2023 at 10:44 PM
does it program ok? do a hard reset, plug in the harness, and then press the pts button twice, led should go "green". push the PTS once more to turn off.
SLP wire should be Green, *(connect the yellow from harness)*
Immo 1 Yellow/black to PINK at the BCM pin 4
Immo 2 Orange/black to Light Green at BCM pin 16
don't need to ground the hood pin, if you ground it, it won't start since it thinks the hood is open
only other thing that could be wrong is it's flashed for the wrong car, or they didn't turn on the 3 X lock. or maybe they turned on Lock, Unlock, Lock
Posted By: wyciwug
Date Posted: January 07, 2023 at 11:26 PM
I am sure all connections are correct
SLP is the middle wire of the 7-pin black connector. NOWAY i miss that.
I have not tried a hard reset. May try that tomorrow.
It was programmed perfectly fine.
-------------
DCD
Posted By: wyciwug
Date Posted: January 08, 2023 at 9:18 AM
After a hard reset, i will have to reflash it?
-------------
DCD
Posted By: silvercivicsir
Date Posted: January 09, 2023 at 8:26 AM
SLP is the most important wire, it is what tells the car to crank.. do you have a pic? *should be* the middle wire, but I would count pins, wire number #4. do you have a multi meter? when you try and do the 3X lock, meter the yellow wire to ensure it's outputting ground.
|