2015 Subaru Outback, Compustar CM900-AS Remote Start, Shutdown
Printed From: the12volt.comForum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=148039
Printed Date: May 03, 2025 at 3:38 PM
Topic: 2015 Subaru Outback, Compustar CM900-AS Remote Start, Shutdown
Posted By: waterresistro
Subject: 2015 Subaru Outback, Compustar CM900-AS Remote Start, Shutdown
Date Posted: May 20, 2024 at 2:22 PM
Hello everyone, newbie here having problems with a new installation on a 2015 outback equipped with key start-automatic.
Using a compustar cm900 with blade-al(FW v2.5).
Updated the CM(FW v1.32) and flashed the blade with cars firmware(FW v2.5).
During initial flashing and the KLON extended programming the led flashed as indicated and most of the functions seem to work except the remote start. The car starts and immediately shuts down throwing an error code 1 on the 2way remote.
I know that means it cannot sense the tach signal and i cannot understand why. When learning tach it confirmed with one flash (and one chirp) it found it. Tried both methods (with start button on remote while engine running and starting and holding brake for 30s) and they both confirm signal is successfully learned. Played with different sensing modes, advanced mode, event went into "assumed 3 sec. start" and it still stops the engine after 1-2 seconds.
This is the connection(type 4) from the blade install guide.
Found a similar thread here on this forum and tried resetting the blade, and starting from zero (fllushing firmware, learnig the key, KLON programming everything smooth) but almos same result. (https://www.the12volt.com/installbay/forum_posts.asp?tid=146186)
The difference being that now it doesn't seem to see i'm trying to learn tach signal. With brake pedal it simply doesn't react, with remote start button it thinks it starts the car remotely. So basically no confirmation of successful/unsuccessful learning and it seems to stay into Tachless mode.
Not sure what to try next and why the inconsistent comportment.
Using a compustar cm900 with blade-al(FW v2.5).
Updated the CM(FW v1.32) and flashed the blade with cars firmware(FW v2.5).
During initial flashing and the KLON extended programming the led flashed as indicated and most of the functions seem to work except the remote start. The car starts and immediately shuts down throwing an error code 1 on the 2way remote.
I know that means it cannot sense the tach signal and i cannot understand why. When learning tach it confirmed with one flash (and one chirp) it found it. Tried both methods (with start button on remote while engine running and starting and holding brake for 30s) and they both confirm signal is successfully learned. Played with different sensing modes, advanced mode, event went into "assumed 3 sec. start" and it still stops the engine after 1-2 seconds.
This is the connection(type 4) from the blade install guide.
Found a similar thread here on this forum and tried resetting the blade, and starting from zero (fllushing firmware, learnig the key, KLON programming everything smooth) but almos same result. (https://www.the12volt.com/installbay/forum_posts.asp?tid=146186)
The difference being that now it doesn't seem to see i'm trying to learn tach signal. With brake pedal it simply doesn't react, with remote start button it thinks it starts the car remotely. So basically no confirmation of successful/unsuccessful learning and it seems to stay into Tachless mode.
Not sure what to try next and why the inconsistent comportment.
Replies:
Posted By: waterresistro
Date Posted: May 20, 2024 at 2:26 PM
Forgot my reference table.
CN1 = main control module connector to ignition switch
CN2 = blade connector
CN3 = gray connector on control module
CN1 = main control module connector to ignition switch
CN2 = blade connector
CN3 = gray connector on control module
Posted By: silvercivicsir
Date Posted: May 22, 2024 at 8:59 AM
Posted By: waterresistro
Date Posted: May 22, 2024 at 8:11 PM