ignition 12v(+) Wire

Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=16975
Printed Date: May 14, 2024 at 6:43 AM

Topic: ignition 12v(+) Wire

Posted By: JDM R
Subject: ignition 12v(+) Wire
Date Posted: July 31, 2003 at 11:51 PM

Where should i tap into the ignition 12v(+) Wire? as shown in this picture: posted_image

and this pic: posted_image

I have a 95 integra and i'm gonin to do a fuel kill switch shown in tha 2nd pic amd a starter kill switch in the 1st pic. where is the best place to tap into the ignition 12v(+) Wire so i can connect it to these switches?

-------------
1995 Integra LS 5 speed
-RSpec106@netscape.net

Replies:

Posted By: JDM R
Date Posted: July 31, 2003 at 11:54 PM

here's the link to the 2nd pic that was soposed to be in the 1st post.
https://www.we-todd-did-racing.com/wetoddimage.wtdr?i=wMTM5NzYxNnM0MTNkZmQzMXk1NDE%3D

-------------
1995 Integra LS 5 speed
-RSpec106@netscape.net

Posted By: draasch
Date Posted: August 01, 2003 at 4:52 AM

Constant 12 volts WHITE IGNITION SWITCH HARNESS

-------------
Good Luck
David
Ace Security
813-376-9778
Tampa
Donate to the 12volt

Posted By: JDM R
Date Posted: August 01, 2003 at 4:55 PM

so i would cut the big white wire that is connected to the ignition switch. Also cut the starter wire that is BLACK/ white. These wires are next to BLACK / YELLOW, yellow, and WHITE/ yellow wires; they connect to the ignition (key switch) on the left side of the steering wheel.

-------------
1995 Integra LS 5 speed
-RSpec106@netscape.net

Posted By: JDM R
Date Posted: August 01, 2003 at 5:09 PM

The white wire and the BLACK/ white wire connect to the under-dash fuse/relay box above where the SRS wires plug into the under-dash fuse/relay box.

so are those wires the right wires to cut?

-------------
1995 Integra LS 5 speed
-RSpec106@netscape.net

Posted By: draasch
Date Posted: August 02, 2003 at 2:02 PM

no do not cut the white wire. you are just getting power from the white wire to work the relays. your starter wire will need to be cut.

-------------
Good Luck
David
Ace Security
813-376-9778
Tampa
Donate to the 12volt

Posted By: JDM R
Date Posted: August 02, 2003 at 9:05 PM

draasch wrote:

no do not cut the white wire. you are just getting power from the white wire to work the relays. your starter wire will need to be cut.

So how do i get power from the white wire if i don't cut into it??

-------------
1995 Integra LS 5 speed
-RSpec106@netscape.net

Posted By: unprofessional
Date Posted: August 02, 2003 at 9:08 PM

You'll probably have to strip back some insulation and solder your power wire to the ignition wire and wrap with some electrical tape.

If there is another safe way of getting +12V from the ignition wire without soldering I'd love to hear it.

Posted By: draasch
Date Posted: August 02, 2003 at 10:22 PM

i didnt mean you couldnt tap into, you cant cut it in two.....

-------------
Good Luck
David
Ace Security
813-376-9778
Tampa
Donate to the 12volt

Posted By: JDM R
Date Posted: August 03, 2003 at 2:39 PM

oh ok i completely understand now thanks fo da info.

-------------
1995 Integra LS 5 speed
-RSpec106@netscape.net