Remote Start from Durango to LeSabre
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=20457
Printed Date: June 09, 2024 at 1:34 AM
Topic: Remote Start from Durango to LeSabre
Posted By: abright52
Subject: Remote Start from Durango to LeSabre
Date Posted: October 23, 2003 at 1:01 AM
I am looking to remove a remote start system from a 1998 Dodge Durango and install it on a 2000 Buick Lesabre.
What additional parts will I need to install this and is there anything that I will need to watch out for?
-------------
Replies:
Posted By: Velocity Motors
Date Posted: October 23, 2003 at 6:43 AM
The Buick has Passkey III that requires a bypass module for remote start. You will need additional relays for the 2 nd IGN, 2 nd ACC & the (-) parking lights for the LeSabre.
-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Posted By: abright52
Date Posted: October 27, 2003 at 1:34 AM
Judging from pictures I've seen, I believe the system is a Prestige APS55. Are there any wiring diagrams or installation instructions online for this system?
-------------
Posted By: Velocity Motors
Date Posted: October 27, 2003 at 7:57 AM
Check out www.audiovox.com and look into their manuals page. ------------- Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Posted By: abright52
Date Posted: October 27, 2003 at 9:43 AM
Thnaks Jeff.
I had tried that last night, but their site was down. It is back up now though. Wasn't sure if that was the right site to go to.
-------------
Posted By: abright52
Date Posted: November 26, 2003 at 11:50 AM
Seem to be having some problems here. I have never installed an Audiovox RS before, I am not growing very fond of it.
The previous installer did not install the program switch, hood switch or anything else beyond plug and play wiring. So, now I am left without those parts.
I have everything plugged in, Door Locks work flawlessly, but when I try to Remote Start it everything powers up and then I get the message on the Information Center "Service Stability System" and it shuts down. It will start will the key in the "Acc" position and once it is started I can remove the key and it will stay running.
I have the Passlock III Bypass installed.
Here is my wiring:
RS - Car
Red - Orange (Constant +)
RED / Whi - Orange (Constant +)
Blue - Pink (IGN)
Yellow - Violet (Starter)
Green - White (IGN 2)
Violet - Brown (ACCY)
Black - Ground
Grey - N/C
GRY/BLK - N/C
Brown - N/C
BRN/BLK - White (Brake)
White - BRN/WHI (Pk Lights)
White - Ground
Lt Blue - Orange (IGN 3 - Through Relay)
Dk Green - White at Coil (Tach)
Yel/Blk - Brown of Bypass
Bypass:
Brown - Yel/Blk of RS
Orange - Orange (Constant +)
Black - Ground
Purple - Purple (Data)
Any help would be greatly appreciated. I was supposed to have this done yesterday, I gave up at 4AM.
-------------
Posted By: abright52
Date Posted: November 26, 2003 at 3:04 PM
Nevermind the previous post, I got it done.
The Purple Accessory wire from the RS was not putting out any power whatsoever, so I bypassed that wire to an IGN wire and everything works!
-------------
Posted By: Velocity Motors
Date Posted: November 26, 2003 at 3:28 PM
Did you use a relay to bypass the wire ? Just curious on the load on that PURPLE wire.
-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
|