I need help with the 555U immobilizer wir
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=21227
Printed Date: August 06, 2025 at 11:31 PM
Topic: I need help with the 555U immobilizer wir
Posted By: henrynguyen
Subject: I need help with the 555U immobilizer wir
Date Posted: November 09, 2003 at 10:00 PM
I have 2002 Accord V6. I bought the 555U immobilizerbut I don't know where the blue remote start negative status output go to? My alarm doesn't have remote starter (-) status output. Where can I connection the (BLUE Remote Start - status Output) to when my alarm doesn't have that wire? Please Help
Thank You
Henry
Replies:
Posted By: Honda99
Date Posted: November 09, 2003 at 10:29 PM
me too........i have a 555H.....i could not know where to connect this wire.......and i have a viper 791XV.....Please anyone help us....thanks
Posted By: Justaguy
Date Posted: November 09, 2003 at 10:44 PM
The status output is basically the same as ignition, or 'ground when running'. Just wire the bypass to a negative output from the starter that comes on with ignition. The bypass has to turn-on either at the same time or before the ignition does to sent the signal to the transponder ring. Hope that helps. -------------
Posted By: Honda99
Date Posted: November 09, 2003 at 11:02 PM
from my Viper 791XV...i have 2 wire Blue(-) status output and Purple(-)200mA starter output.......so which one i use.......from your post you said ignition but which one. i have ingition 1 and ignition 2. thanks
Posted By: Justaguy
Date Posted: November 09, 2003 at 11:11 PM
Use the blue- status output(same as ignition but negative) to the 555h to trigger the bypass, and you will also need to power it up with constant power(red wire on 555h i believe. Also make sure that the power wire is fused.
-------------
Posted By: Honda99
Date Posted: November 09, 2003 at 11:34 PM
thank...i did that but my car still can not start....can you tell me why?
Posted By: Justaguy
Date Posted: November 09, 2003 at 11:39 PM
did you program the 555h right. Test the wires going into the 555 and make sure that it is getting power and ground before starting. try starting the car with the bypass unplugged and a key in the ignition. that will tell you if you have a transponder issue or not. But without knowing all the info, it's pretty hard to troubleshoot on a forum. -------------
Posted By: Honda99
Date Posted: November 09, 2003 at 11:45 PM
you're mean unplugged the bypass module and insert the vehicle key into the ignition, but do not turn it on and then use a remote to start.
Posted By: Honda99
Date Posted: November 09, 2003 at 11:48 PM
i think i getting power because a led light up. the parking light turn on and off for a few time and doesn't doing any thing.
you're mean unplugged the bypass module and insert the vehicle key into the ignition, but do not turn it on and then use a remote to start.
Posted By: Justaguy
Date Posted: November 09, 2003 at 11:48 PM
ya, that will let you know for sure that the problem is a bypass one or not, if the car doesn't start with the key in the ignition, then there is a problem with the wires on the remote start, not just the 555h
-------------
Posted By: Honda99
Date Posted: November 10, 2003 at 12:03 AM
yah.....i was try it doesnt' start with the remote and i try start with the key it crank but doen't. and i but back the bypass module and start with a key. it's start but the remote doesn't. anyway thank alot. i will double check my wiring...do you know how to test a wiring to make sure i have a right wire?
Posted By: Justaguy
Date Posted: November 10, 2003 at 12:07 AM
If you don't have a computer-safe test light then use a multi-meter to test your wires, and NEVER go near the airbag wires(usaully in a yellow jacket). -------------
Posted By: JWorm
Date Posted: November 10, 2003 at 5:37 AM
If you unplug the 555H, the car won't even start by key because the immobilizer wiring will be interrupted. Pull the fuse in the 555H out, put a key in the ignition and try to remote start it. If it doesn't start, something else is the problem. If it does start, you wired the 555H wrong, or it hasn't learned the code.
You can only test some of the wires that get connected to the 555H. Some of the wires are data and can't be tested. Do NOT use a test light. If you remove the steering column cover and find the green plugs near the ignition cylinder you will find the wires. The colors will match the colors listed on the instructions exactly.
Posted By: Honda99
Date Posted: November 10, 2003 at 2:04 PM
i pull the fuse out and starter with the remote still doesn't but it start with the key. i program exacly from the installation intruction but i don't know it has learned the code or not. not idea.
Posted By: henrynguyen
Date Posted: November 10, 2003 at 4:15 PM
I still cannot find the - output wire. Anyone know what color/location of the starter - output wire for 2002 accord V6. Any help would be nice.
Thanks
Posted By: JWorm
Date Posted: November 10, 2003 at 10:18 PM
henrynguyen, the (-) trigger input on the 555U gets hooked to a wire on the remote starter. What model remote start are you using? Having all the relevant info would be nice.
Posted By: henrynguyen
Date Posted: November 10, 2003 at 10:26 PM
JWorm] wrote:
henrynguyen, the (-) trigger input on the 555U gets hooked to a wire on the remote starter. What model remote start are you using? Having all the relevant info would be nice.
I'm Using Crime Stopper Model: 2009 FM 2 way alarm system. Thank you for your help. Henry
Posted By: alpha
Date Posted: November 10, 2003 at 10:44 PM
henrynguyen...i think you can use the orange wire (-) output
Posted By: Honda99
Date Posted: November 11, 2003 at 12:33 AM
hi..Justaguy.....i found a problem from my car.....the problem is a key,. i use other honda key and try program again it work.....so thank for your help..
|