I am desperate for a wiring diagram for an alarm install on a Dodge Viper T10 - 2002 model.
I am in the UK so have very little access to info other than you through you great guys.
Thanks a lot
Naughtydog
| ITEM | WIRE COLOR |POL| WIRE LOCATION |
| 12V|red & pink/black |+ |ignition harness |
| STARTER|yellow |+ |ignition harness |
| IGNITION|blue |+ |ignition harness |
| ACCESSORY|BLACK/ orange |+ |ignition harness |
| SECOND ACCESSORY|BLACK/ white |+ |ignition harness |
| POWER LOCK|WHITE/ green *1 |+ |lt blu plug,pin D14 @ EEM *2|
| POWER UNLOCK|same wire | | |
| LOCK MOTOR| | | |
| UNLOCK MOTOR| | | |
| DISARM DEFEAT| | | |
| PARKING LIGHTS +|BLACK / YELLOW *3 | |grn plug, pin B @ EEM *2 |
| HEADLIGHTS|lt GREEN/ red |+ |headlight switch |
| DOOR TRIGGER|*4 |- |lt blue plug @ EEM *2 |
| DOME SUPERVISION|yellow |- |grn plug,pin 6,under fusebox|
| TRUNK/HATCH PIN|gray/black(GTS only)|- |lt blu plug,pin C14 @ EEM *2|
| HOOD PIN|BROWN / tan |- |lt blu plug,pin C12 @ EEM *2|
| FCTRY ALARM ARM|arms with lock *5 | | |
|FCTRY ALRM DISARM|lt GREEN/ orange |+ |lt blu plug,pin C11 @ EEM *2|
| TACHOMETER|gray/lt blue | |gry plug, pin 31 @ PCM *6 |
| SPEED SENSE|WHITE/ tan | |radio |
| BRAKE WIRE|white |+ |brake pedal switch |
| HORN TRIGGER|BLACK/ red |- |lt blu plug, pin C3 @ EEM *2|
| WIPERS|brn/wht(L),RED / yel(H|- |steering column |
| LF WINDOW UP/DN|lt blue - white |A |switch on center console |
| RF WINDOW UP/DN|brown - purple |A |switch on center console |
| RADIO 12V|pink |+ |radio |
| RADIO GROUND|black |- |radio |
| RADIO SWITCH|RED / white |+ |radio |
| RADIO ILLUMINATE|BLACK / YELLOW |+ |radio |
| POWER ANTENNA|GREEN/ red |+ |radio |
| LF SPEAKER|lt grn/pu-lt grn/grn| |power amplifier *7 |
| RF SPEAKER|lt blu/pu-lt blu/grn| |power amplifier *7 |
| LR SPEAKER|wht/pur - wht/grn | |power amplifier *7 |
| RR SPEAKER|tan/pur - tan/grn | |power amplifier *7 |
Notes:
*1 Pulse the wire once will lock the doors and pulsing it again will unlock the doors. To OPEN the driver door pulse positive to pink/white in pin D11, in the lt blue plug of the EEM. To OPEN the passenger door pulse positive to ORANGE / white in pin D12. *2 The EEM (Electronic Entry Module) is located on the driver side of the transmission tunnel. *3 Also found tan at the headlight switch. *4 The driver door trigger is BLACK/ lt blue in pin C15, and the passenger door trigger is tan/red in pin C16. Use both wires and diode isolate each. *5 The factory alarm will arm with lock if it see the driver door open. Use the lock output to pulse the driver door trigger the same time as lock. *6 The PCM (Powertrain Control Module) is on the driver fender under the power distribution center. The tach wire is also located behind the instrument cluster. *7 The power amplifier is located on the driver side of the trunk.
-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Cheers Jeff.
Do you know of an immobilisation point other than the starter. I think it has twin fuel pumps.