PRO9232S installation Chevrolet Venture

Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=23245
Printed Date: May 15, 2025 at 9:58 PM

Topic: PRO9232S installation Chevrolet Venture

Posted By: dude_electric
Subject: PRO9232S installation Chevrolet Venture
Date Posted: December 23, 2003 at 2:21 AM

Hi Guys,

I need instructions on how to install an AUDIOVOX PRO9232S to a 2003 Chevrolet Venture.I already have the wiring information for the VAN but i dont know specifically whichwires to tap into; (example: ARM/DISARM - should i tap directly to the door actuators or do i use theARM/DISARM output of the keyless entry module.) Preferably if somebody could tell me which specific wires from the Venture Van i will use to connect the wires described in the PRO9232S installation diagram. - arm, disarm#1, disarm#2, door switch trigger, ignition, +12V, GND, etc.

-------------
DUDE_ELECTRIC

Replies:

Posted By: Geeque
Date Posted: December 23, 2003 at 9:22 AM

If you have the wiring for the van you should have the correct wires and locations, here I'll give you the wiring info I have:

SecurityBattery           RED       (+)  IGNITION SWITCH HARNESSIgnition          PINK      (+)  IGNITION SWITCH HARNESSStarter01         YELLOW    (+)  IGNITION SWITCH HARNESSParkingLights     BROWN     (+)  AT VEHICLE LIGHT SWITCHRemote StartBattery           RED       (+)  IGNITION SWITCH HARNESSIgnition          PINK      (+)  IGNITION SWITCH HARNESSIgnition02        WHITE     (+)  IGNITION SWITCH HARNESSAccessory01       ORANGE    (+)  IGNITION SWITCH HARNESSStarter01         YELLOW    (+)  IGNITION SWITCH HARNESSAntiTheftType     PASSKEY IIIAntiTheftSystem	  AN RF SIGNAL ACTIVATED SYSTEMKeySense          LIGHT GREEN (-)  IGNITION SWITCH HARNESSTach              WHITE     (-)  LARGE HARNESS ON PASSENGER SIDE OF ENGINEParkingLights     BROWN     (+)  AT VEHICLE LIGHT SWITCHBrakeLights       WHITE     (+)  AT SWITCH ABOVE BRAKE PEDAL ReverseLights     LIGHT GREEN (+)  IGNITION SWITCH HARNESSDoorlocks / WindowPowerUnLock       ORANGE / BLACK (-)  IN HARNESS IN DRIVERS KICKPANELPowerLock         RED / BLACK (-)  IN HARNESS IN DRIVERS KICKPANELDriverDoorMotor01 TAN       (+)DriverDoorMotor02 GRAY      (+)  IN HARNESS IN DRIVERS KICKPANELConvenienceHeadLights        YELLOW    (+)  AT VEHICLE LIGHT SWITCHLowSpeedWipers    PINK      (+)  AT VEHICLE WIPER SWITCHTrunkRelease      BLUE      (-)  IN HARNESS IN PASSENGER KICKPANEL

-------------
Gary Kline
MECP Master Technician

Posted By: dude_electric
Date Posted: December 23, 2003 at 4:52 PM

the alarm has two DISARM inputs (DISARM#1 and DISARM#2), and one ARM input. Which of of the van wiring mentioned above should i use; As i see there are more than one options;

Doorlocks / Window
PowerUnLock       ORANGE / BLACK (-) IN HARNESS IN DRIVERS KICKPANEL
PowerLock         RED / BLACK (-) IN HARNESS IN DRIVERS KICKPANEL
DriverDoorMotor01 TAN       (+)
DriverDoorMotor02 GRAY      (+) IN HARNESS IN DRIVERS KICKPANEL
Convenience

Also, if i use the power lock/unlock mentioned above, would the existing DRIVER DOOR PANEL LOCK/UNLOCK SWITCH disarm the alarm ?

thanks.

-------------
DUDE_ELECTRIC

Posted By: dude_electric
Date Posted: December 23, 2003 at 5:15 PM

Hi,

I also would like to get info on which wires to use for the door triggers - DRIVER, PASSENGER, SLIDING, TRUNK. As i see,there are a lot of possibilities to tap, i cant seem to determine which of these wires to use.

thanks

-------------
DUDE_ELECTRIC

Posted By: sparkie
Date Posted: December 24, 2003 at 9:45 AM

Your two disarm wires go to the tan wires that feed the the door lock actuators. The arm wire goes to the grey wire for the driver's door actuator. You must hook up the disarm wires carefully, otherwise the alarm won't work correctly. Hook up the disarm wire that if is powered won't allow the alarm to disarm to the passenger side lock motor. The wires can be found in the kick panels of each front door. The doorpin wires are tan, dark blue and orange. They must be diode isolated and can be found at the BCM qbove the passenger side kick panel. Use these summed wires to connect to a relay's terminal #85. Terminal #86 put to a fused 12 volt + source. Terminal # 30 to ground. Terminal #87 to the brown wire for your alarm. Using this relay will eliminate a falsing problem caused by these vehicles.

-------------
sparky