95 explorer, viper 791 xv

Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=25112
Printed Date: July 13, 2025 at 1:45 PM

Topic: 95 explorer, viper 791 xv

Posted By: wtcook8657
Subject: 95 explorer, viper 791 xv
Date Posted: January 22, 2004 at 11:00 PM

i'm installing the new viper 791 xv in a 95 explorer. i'm new to alarm installation. so if anyone has any information and/or tips they could could give to help me out along the way

Replies:

Posted By: joebizz
Date Posted: January 23, 2004 at 12:13 AM

I just put it in my infiniti, its awesome.. sorry i have no tech info on that car.

-------------

Posted By: Basscoholic23
Date Posted: January 23, 2004 at 12:28 AM

constant -Yellow (2)

Ingnition1-light GREEN/ purple

Ignition 2-gray / YELLOW

Ignition 3-gray / YELLOW

Starter-RED / light blue

Accesorries-BLACK/ light green

Brake-light green -above brake pedal

Parking lights-brown (+) -below kick panel

Door trigger-BLACK/ blue -(+)below kick panel

Tach-tan / YELLOW- At ICM in front of engine compartment

lock-pink / YELLOW (-) below kick panel

unlock-pink/light green (-) below kick panel

Posted By: wtcook8657
Date Posted: January 24, 2004 at 8:13 AM

there is a four pin harness that attaches to the relay satalite and i can't locate the description of these wires in the manual and have no clue what they are. does anyone know what they are and hook to. thanks

Posted By: joebizz
Date Posted: January 24, 2004 at 8:23 AM

look at the last page, the description is there....

Blue (-) Status Output

Orange (-) 200mA 2nd acessory output

Purple (-) 200mA starter output

Pink (-) 200mA 3rd Ignition output

Good luck dude!

-------------

Posted By: wtcook8657
Date Posted: January 24, 2004 at 2:24 PM

does anyone know where and what color the dome light wire is

Posted By: profuse007
Date Posted: January 24, 2004 at 2:26 PM

Posted By: wtcook8657
Date Posted: January 24, 2004 at 6:25 PM

i'm haveing a problem figuring out what the WHITE/ blue remote start (-) activation input hooks up to. could some one please explaine this to me

thanks

Posted By: wtcook8657
Date Posted: January 24, 2004 at 9:12 PM

can anyone help me with this???

Posted By: advanced529
Date Posted: January 24, 2004 at 9:47 PM

The WHITE/ blue wire can be hooked up to a momentary switch to activate the alarm by pressing it one to three times depending on the the programming of the alarm.. It carries the same function of the remote start button on the remote.. Not Necessary..

Posted By: wtcook8657
Date Posted: January 24, 2004 at 11:44 PM

i have a few more questions about the wiring

for the factory disarm output is it neccesary to use a relay?

the alarm has a factory alarm rearm wire (GREEN / WHITE) but i haven't been able to find what wire to hook this into.

in the remote start secondary harness the blue/white (-) status output what does this connect to?

in the four pin connector that connects to the relay satellite: for blue (-) status output do i tie this into the blue/white (-) status output in the remote start secondary harness and what do i connect this to, the orange (-) 2nd accessory output and the purple (-) starter output, what do i connect these to? there is also a pink (-) 3rd igntion output that i need to know what to connect this to.

Posted By: wtcook8657
Date Posted: January 25, 2004 at 12:35 AM

Can anyone help me out with this

Posted By: Velocity Motors
Date Posted: January 25, 2004 at 12:57 AM

for the factory disarm output is it neccesary to use a relay?

No need for a relay on this connection.

the alarm has a factory alarm rearm wire (GREEN / WHITE) but i haven't been able to find what wire to hook this into.

Arms on lock only with door open. It is necessary to send a signal to door trigger as well as lock to arm factory alarm.

in the remote start secondary harness the blue/white (-) status output what does this connect to?

This wire connects to modules for security bypasses or door lock interface modules. Anything that you may need to turn on when remote starting, but turn off when you insert the key into the ignition to take over the remote starter.

in the four pin connector that connects to the relay satellite: for blue (-) status output do i tie this into the blue/white (-) status output in the remote start secondary harness and what do i connect this to,the orange (-) 2nd accessory output and the purple (-) starter output, what do i connect these to? there is also a pink (-) 3rd igntion output that i need to know what to connect this to.

You do not connect any wires from the alarm back into any other harnesses on the alarm. Check the installation manual for descriptions of all these wires to help you install these wires.

-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA

Posted By: wtcook8657
Date Posted: January 25, 2004 at 1:20 AM

there isn't a description of the wires on the four pin relay satellite. it just states what they are as in what i had listed. i am a beginner so any help would be greatly appreciated.

Posted By: wtcook8657
Date Posted: January 25, 2004 at 2:42 AM

can anyone tell me what to hook up to for the four pin pin relay satelite. i can not find anything in the instructional manual on them or i may just not be seeing it. please help

Posted By: wtcook8657
Date Posted: January 25, 2004 at 3:02 AM

can anyone not tell me how to hook up the wires please

Posted By: wtcook8657
Date Posted: January 25, 2004 at 5:46 AM

is there anyone out there that can answere my questions

''PLEASE"