98 Dakota Power Door Locks
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=27209
Printed Date: May 18, 2024 at 12:30 PM
Topic: 98 Dakota Power Door Locks
Posted By: robbain
Subject: 98 Dakota Power Door Locks
Date Posted: February 25, 2004 at 11:17 AM
I'm installing a Crimestopper CS2015FM TW1 in my 1998 Dakota. I'm trying to figure out how to hook up the power door locks. I think they are reverse polarity and require extra relays. Any help or diagrams would be greatly appreciated. Thanks. Rob
Replies:
Posted By: robbain
Date Posted: February 25, 2004 at 11:21 AM
Also, the vehicle has factory power locks but no keyless entry. Thanks. Rob
Posted By: draasch
Date Posted: February 25, 2004 at 12:20 PM
what are the outputs on the alarm????
Power Lock ORN/PPL OR GRN/BLK 16 PIN CONNECTOR BEHIND ** #203
Power Unlock PINK/VIOLET FUSE BLOCK IN DRIVER KICK PANEL
203 - See Reversal Rest At Ground Door Lock Diagram W/Or WO Keyless.
https://wiringinstructions.com/203.htm------------- Good Luck
David
Ace Security
813-376-9778
Tampa
Donate to the 12volt
Posted By: davedyer79
Date Posted: February 25, 2004 at 12:31 PM
A little easier wiring diagram. The diagram that draasch sent is for a DLS plug from Omega, which would make the connections a lot easier. If you do not have the DLS, grab two SPDT relays from the automotive store or Circuit City and wire the like this diagram https://www.the12volt.com/doorlocks/page3.asp#5w This will work if the outputs of your alarm is negative outputs, which it should be. Good luck. ------------- davedyer79
Posted By: Sandungero24
Date Posted: February 26, 2004 at 3:32 PM
Posted By: robbain
Date Posted: February 26, 2004 at 3:59 PM
Another thing I noticed on the wiring diagram was that it lists BLACK/ orage for accessory and for ignition 2. Does this mean there are two BLACK/ orage wires? or do I just use it for the accessory and there is no ignition 2? Thanks. Rob
Posted By: draasch
Date Posted: February 26, 2004 at 4:05 PM
Remote Start
Tach Signal BLACK/ GRAY AT IGNITION COIL *
Ignition #2 BLACK/ ORANGE IGNITION SWITCH HARNESS (HEAT/AC)
Ignition #3 N/A
Accessory BLACK/ WHITE IGNITION SWITCH HARNESS
Neutral Safety BLACK/ WHITE (-) AT POWERTRAIN CONTROL MODULE **
Brake Light WHITE/ TAN (+) AT SWITCH ABOVE BRAKE PEDAL
Reverse Light VIOLET/BLACK (+) AT SWITCH ON TRANSMISSION
Rear Window Defrost N/A
* Ignition Coil Is Located On Passenger Front Of Engine. BLACK/ GRAY Wire Is Also Located At Powertrain Control Module (PCM) In A Black 32 Pin Connector. ** Powertrain Control Module (PCM) Is Located On Passenger Rear Of Engine Next To Strut Tower.
------------- Good Luck
David
Ace Security
813-376-9778
Tampa
Donate to the 12volt
Posted By: daniel2002p
Date Posted: February 26, 2004 at 8:00 PM
your locks are reverse polarity, but BLACK/ orange is acc and lt blue is ignition.
-------------
2005 Toyota Corolla S
1.8L VVT-i I-4
Always double check your wires with a DMM!!!
Do Not Use A Test Light!!!
MECP Certified Installer!
Best Buy 665 - IN IT TO WIN IT! TEAM MOBLE!
Posted By: robbain
Date Posted: February 26, 2004 at 9:30 PM
One person tells me that BLACK/ orange is ign 2 and somebody else says it is acc. I've been told that dk blue is ign, now it's lt blue. Who is right??? Rob 1998 Dakota
Posted By: Sandungero24
Date Posted: February 26, 2004 at 9:32 PM
| Ignition 1 | Dark Blue | Ignition Switch Harness | | Ignition 2 | BLACK/ Orange | Ignition Switch Harness (Heat/AC) | | Accessory | BLACK/ Orange | Ignition Switch Harness |
Posted By: Velocity Motors
Date Posted: February 26, 2004 at 9:36 PM
Some wiring diagrams differentiate the DARK BLUE and the BLUE wires. It's the same when you look under the dash at the wires. Look for the BLUE wire ( if may look dark blue, but it really doesn't matter because it will be only solid blue wire in the ignition harness ). The ACC is BLACK/ ORANGE ( you can test this with your DMM & like I said before, some wiring diagrams say it's a 2nd IGN wire but it still operates the heater/AC like a ACC wire does ) and 2nd ACC is BLACK/ WHITE
-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Posted By: robbain
Date Posted: February 26, 2004 at 11:19 PM
Thanks for all the help guys. Rob
Posted By: robbain
Date Posted: February 26, 2004 at 11:31 PM
One final question. Will it work if I accidentally interchange the ign2 and the acc wires. Do they operate the exact same? or are they different from eachother? Thanks again. Rob
Posted By: robbain
Date Posted: February 28, 2004 at 10:15 AM
So does it matter if I interchange the ign2 and the acc? I have some people saying BLACK/ orange is acc and 2nd acc is BLACK/ white. Other tell me BLACK/ orange is ign2 and BLACK/ white is acc. Who's right??? Does it matter if they are switched??? Thanks. Rob
Posted By: draasch
Date Posted: February 28, 2004 at 11:35 AM
Ignition 12 volts D BLUE IGNITION SWITCH HARNESS
Accessory BLACK/ WHITE IGNITION SWITCH HARNESS
Ignition #2 BLACK/ ORANGE IGNITION SWITCH HARNESS (HEAT/AC)
i would make sure you power up the blk/orange ------------- Good Luck
David
Ace Security
813-376-9778
Tampa
Donate to the 12volt
Posted By: JMaxx93
Date Posted: February 28, 2004 at 11:38 AM
it really won't affect any thing if you mix up the ign acc wires as long as you put an ign wire from the alarm to an acc wire on the car not the other way around.
|