Power Door Locks

Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=28454
Printed Date: July 14, 2025 at 4:18 AM

Topic: Power Door Locks

Posted By: msilverton
Subject: Power Door Locks
Date Posted: March 16, 2004 at 1:14 AM

Can anyone provide some direction to hookup power door locks to a Clifford 400.

I have installed a two wire actuator in the driver's door. How does the six wire from the harness go?

Thanks in advance,

Mike

Replies:

Posted By: Javelin3o4
Date Posted: March 16, 2004 at 3:08 AM

are you using the 451m module from DEI? if so it should have a digram on the backside of the relay.

Posted By: laren5
Date Posted: March 16, 2004 at 3:28 AM

I dont have the diagram right know,

but I think almost all DEI have these 6 colors:

GREEN/ black : connect to green wire of actuator

Blue/black : connect to blue wire of actuator

WHITE/ black : connect to ground

BROWN / black : connect to ground

Violet/black en Violet : connect to 12 volt (+) and use a fuse. The fuse must be rated at 7.5 AMP per actuator. So if u use 2 actuators then 15 AMP fuse.

Greetings

-------------
Clifford Alarms

Posted By: RalphWiggum
Date Posted: March 16, 2004 at 11:18 PM

I think that this will help you.

posted_image

Posted By: RalphWiggum
Date Posted: March 16, 2004 at 11:20 PM

Sorry the pic didn't work...visit this site.

https://clifford.com/guides/wiring/keyless_wiring.pdf

go to page # 2 on this .pdf document and use diagram #4

I hope that helps!

Posted By: msilverton
Date Posted: March 17, 2004 at 1:27 AM

RalphWiggum wrote:

Sorry the pic didn't work...visit this site.
https://clifford.com/guides/wiring/keyless_wiring.pdf
go to page # 2 on this .pdf document and use diagram #4
I hope that helps!

Posted By: msilverton
Date Posted: March 17, 2004 at 1:44 AM

RalphWiggum wrote:

Sorry the pic didn't work...visit this site.
https://clifford.com/guides/wiring/keyless_wiring.pdf
go to page # 2 on this .pdf document and use diagram #4
I hope that helps!

Let's try that again. Is the FACTORY LOCK MODULE built into the alarm itself?

Mike

Posted By: RalphWiggum
Date Posted: March 17, 2004 at 12:40 PM

The relay is built into the brain. Looking at the 6-wire bunch, take the RED / green & RED / orange wires, twist them together, connect an inline fuse holder with a 20A fuse and attach to positive battery post. Now take the gray/orange & gray/green wires and twist them together and connect them to ground. The WHITE/ green controls locking & WHITE/ orange controls unlocking or vice-versa, you can connect a multi-meter and see which wire pulses when you arm the alarm, that would be your locking lead.

Posted By: RalphWiggum
Date Posted: March 17, 2004 at 12:42 PM

I didn't know what you meant at first regarding the FACTORY LOCK MODULE. That does not pertain to your install. Look again on page #2 from that link and the wire diagram labeled Diagram #4 is the one you will need to pay attention to.

Posted By: msilverton
Date Posted: March 17, 2004 at 2:35 PM

RalphWiggum wrote:

I didn't know what you meant at first regarding the FACTORY LOCK MODULE. That does not pertain to your install. Look again on page #2 from that link and the wire diagram labeled Diagram #4 is the one you will need to pay attention to.

I tried diagram #3 but it didn't work. Then I went to #4 as I had installed one of the actuators myself. Works like a charm. The lock/unlock mechanism seems to pulse three time on the unlock, and my Wizard software is not the PRO version ( I don;t think anyways) as I cannot access the installer programmable features with it.

But the locks do lock and unlock which is a good thing.

Thanks for the advice,

Mike