93 ford probe gt alarm/remote start
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=29034
Printed Date: July 07, 2025 at 4:45 PM
Topic: 93 ford probe gt alarm/remote start
Posted By: bpm687
Subject: 93 ford probe gt alarm/remote start
Date Posted: March 25, 2004 at 7:35 PM
Hello, I have a 2-way LCD alarm with remote start. I want to install this alarm myself because just about every shop around here wants $200 because I didn’t buy it from them. Are there any hints or tips that will help me out like where to mount the brain and switches. This alarm has a window module and a glass sensor. Im pretty good with electronics but I have never installed an alarm before. I also have a 93 ford probe gt
Replies:
Posted By: profuse007
Date Posted: March 25, 2004 at 8:06 PM
what type of unit is this?
-------------
Houston,TX
"The two most common elements in the universe are H+ and stupidity" (Ellison).
Posted By: bpm687
Date Posted: March 25, 2004 at 8:16 PM
Impulse..
Posted By: Javelin3o4
Date Posted: March 25, 2004 at 10:40 PM
FORD, PROBE, 1993, Power Lock
Lock requires a positive trigger. Unlock requires a positive trigger through a 4,700 ohm resistor. Must use relays for both lock and unlock. FORD, PROBE, 1993, Trunk/Hatch PinIn a blue 22-pin plug. FORD, PROBE, 1993, Horn TriggerIn orange plug with air bag wires.
Posted By: bpm687
Date Posted: March 25, 2004 at 11:37 PM
Thanks now is there any tips on where I should mount the unit and Where do I put the glass sensor
Posted By: bpm687
Date Posted: March 25, 2004 at 11:39 PM
Also for the 12v I dont have to run it to the battery like the manual says to do?
Posted By: bpm687
Date Posted: March 25, 2004 at 11:42 PM
And I forgot to say.. Do I have to take my dash apart or just the stearing Column
Posted By: draasch
Date Posted: March 26, 2004 at 10:16 PM
most of the time you will only have to remove the lower dash (under the column) and maybe a kick panel ------------- Good Luck
David
Ace Security
813-376-9778
Tampa
Donate to the 12volt
Posted By: bpm687
Date Posted: March 27, 2004 at 9:52 PM
So where do I put all the sensors Glass and shock
Posted By: markcars
Date Posted: March 28, 2004 at 8:20 AM
Glass sensors usually have a microphone at the end of a shielded cable, which needs to be put in a hidden place but does Not need to be taking the vibration but only "sound" frequency of breaking glass.
Shock sensors, I've had hell installing one myself. I've heard everyone say to install it on a firm metal part of the car, the most sensitive part being tied as tightly as possible on the steering column, but I've had not much luck. I am sure you'll do better than me.
Good luck.
Posted By: bpm687
Date Posted: March 28, 2004 at 6:52 PM
Yeah Ive heard to tie the shock sensor to the harness
Posted By: bpm687
Date Posted: April 03, 2004 at 12:20 PM
And for the window roll up where do I find the wires for this do I go into the drivers door panel or is it in the kick panel?
|