directed dual shock sensor wiring
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=30930
Printed Date: May 06, 2024 at 3:22 AM
Topic: directed dual shock sensor wiring
Posted By: davidwp13
Subject: directed dual shock sensor wiring
Date Posted: April 23, 2004 at 9:53 PM
Hi I am trying to hook up the stinger dual stage sensor that CAME with my Python 660XP and am having trouble understanding the diagrams??? I hope no one minds if I send pics. IF I can please help on how to wire. Damn I could not get to send pics. My shock sensor has a blue a red a black and a green that is not connected at one end and a jumper ( green ) at the other end the inst. say to hook up without diodes "cut" green and then I get lost
-------------
David
Replies:
Posted By: kgerry
Date Posted: April 24, 2004 at 11:40 AM
it should have plugs on both ends and just plugs into the main brain unit....
-------------
Kevin Gerry
Certified Electronics Technician
MECP First Class Installer
Owner/Installer
Classic Car Audio
since 1979
Posted By: mobiletoys2002
Date Posted: April 24, 2004 at 1:03 PM
the green is for an extra sensor just plug harnesses in and you are good to go tape that green wire up and that is all !!
Posted By: davidwp13
Date Posted: April 24, 2004 at 1:16 PM
Thanks for the help, I guess I have another problem??? The light in the shock sensor does light at times BUT I can shake and push the vehicle and I get No response not even " warn away " I get the proper chirps when I arm and disarm?? 1 and then 2 If I disabled that zone by mistake wouldn't it let me know with chirps when I arm it??
-------------
David
Posted By: mobiletoys2002
Date Posted: April 24, 2004 at 1:19 PM
yes it would let you know on arm!! did you turn the shock sensor up with taht little screw inside it?
Posted By: davidwp13
Date Posted: April 24, 2004 at 1:42 PM
No I did not know about that. I understand that these are intended for professional install only, BUT the directions are so vague,, I guess not to yall. Do I turn it clockwise to increase sensitivity ?? and about how much at a time??
-------------
David
Posted By: jimmeezgolfvr6
Date Posted: April 24, 2004 at 8:32 PM
you mentioned that you're shaking and pulling the car? those motions are not likely going to help you trigger any shock sensor. try hitting the car with your fist....preferrably with the doors and windows closed (it's more accurate that way). shock sensors dectect impact and vibration, not movement.
also, after you've armed the alarm, wait around 20 seconds at least before you start testing it. otherwise, if the alarm senses a trigger from the shock sensor too soon after having been armed, it will tend to turn off that "zone" and ignore subsequent triggers.
good luck!
Posted By: davidwp13
Date Posted: April 25, 2004 at 11:06 AM
Is there an UP/DOWN, or does it need to level?? or can it be mounted in any position? The dual stage shock sensor?
-------------
David
Posted By: madmods
Date Posted: April 25, 2004 at 6:41 PM
Tie wrap it to a wiring harness. Make sure the adjustment screw faces where you can reach it. Did you plug it in to the brain? So you have 2 green wires? what do you mean there both not connected? Is there a plug on the end of the red,black,and blue wire? Send me pics to ferrari_export@yahoo.com and I will try to help you.
|