2001 infinty I30 Alarm wiring diagram
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=34629
Printed Date: May 09, 2025 at 2:51 AM
Topic: 2001 infinty I30 Alarm wiring diagram
Posted By: SIK_9D1
Subject: 2001 infinty I30 Alarm wiring diagram
Date Posted: June 26, 2004 at 1:51 PM
I hooked up a viper security system in my 2001 infinity I30 everthing works fine but when i disarm it the factory alarm goes off with it. Is there a factory disarm wire somewere can anybody help?
-------------
SIK_9D1
Replies:
Posted By: jfk51502003
Date Posted: June 26, 2004 at 4:11 PM
DIRECTWIRE™ WIRING INFORMATION - INFINITI / I30 / 2001 / Security[PRINT THIS PAGE]
| 12volts | green | + | ignition harness | | Starter | BLACK/ red or blk/wht | + | ignition harness | | Ignition | BLACK/ red (smaller) | + | ignition harness | | Power Lock | gray | - | pin 23 at SECU | | Notes: The SECU (Smart Entrance Control Unit) is located to the passengers side of the steering column. | | Power Unlock | BROWN / yel | - | pin 35 at SECU | | Notes: The SECU (Smart Entrance Control Unit) is located to the passengers side of the steering column. | | Lock Motor | purple | | pin 15 at SECU | | Notes: The SECU (Smart Entrance Control Unit) is located to the passengers side of the steering column. | | Unlock Motor | WHITE/ black | | pin 13 at SECU | | Notes: The SECU (Smart Entrance Control Unit) is located to the passengers side of the steering column. | | Disarm Defeat | GREEN/ YELLOW | | pin 14 at SECU | | Notes: The SECU (Smart Entrance Control Unit) is located to the passengers side of the steering column. | | Parking Lights+ | RED / blue | | driver kick panel | | Notes: Can also find RED / green or RED / yellow at fuse box. | | Parking Lights- | lt. blue | | headlight switch | | Hazards | | | | | Turn Signal(L) | | | | | Turn Signal(R) | | | | | Door Trigger | | | SECU | Notes: The SECU (Smart Entrance Control Unit) is located to the passengers side of the steering column.
Find lt. blue for the drivers door in pin 29, RED / blue for the passenger front door in pin 40, and RED / white for the rear doors in pin 28. Use all 3 wires and diode isolate each. | | Dome Supervision | use door trigger | | | | Trunk/Hatch Pin | purple / YELLOW | - | pin 38 at SECU | | Notes: The SECU (Smart Entrance Control Unit) is located to the passengers side of the steering column. | | Hood Pin | yellow/red | - | pin 27 at SECU | | Notes: The SECU (Smart Entrance Control Unit) is located to the passengers side of the steering column. | | Trunk/Hatch Release | blue | | pin 12 at SECU | Notes: Requires a high-current ground for activation.
The SECU (Smart Entrance Control Unit) is located to the passengers side of the steering column. | | Power Sliding Door | | | | | Factory Alarm Arm | ORANGE / black | - | pin 41 at SECU | | Notes: The SECU (Smart Entrance Control Unit) is located to the passengers side of the steering column. | | Factory Alarm Disarm | ORANGE / blue | - | pin 30 at SECU | | Notes: The SECU (Smart Entrance Control Unit) is located to the passengers side of the steering column. | | Disarm No Unlock | | | | | Tachometer | WHITE/ green | | instrument cluster | | Notes: Located on the rear of the instrument cluster in the white plug. Do not start the car with the cluster unplugged. Can also find the WHITE/ green at the ECM located in the front of the center console on the transmission hump. The wiring is easily reached by removing the panel just to the front of the center console on the passenger side. | | Horn Trigger | GREEN / WHITE | - | steering column | | Memory Seat 1 | | | | | Memory Seat 2 | | | | | Memory Seat 3 | | | |
 | Immobilizer Bypass Module: | Required: Yes | Type: Transponder | Part #: 556U or 555U | | Notes: N/A |
This wiring information is being provided free of charge on an "as is" basis, without any representation or warranty. It is your responsibility to verify any circuit before interfacing with it using a digital multimeter.
Directed electronics, Inc. assumes no responsibility with regards to the accuracy or currency of this information. Proper installation in every case is and remains the responsibility of the installer. DEI assumes no liability or responsibility resulting from improper installation, even in reliance upon this information. |
|
Posted By: SIK_9D1
Date Posted: June 27, 2004 at 1:42 AM
thanks jfk ------------- SIK_9D1
Posted By: jfk51502003
Date Posted: June 27, 2004 at 11:28 AM
|