remotestart, engine doesn’t crank
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=35084
Printed Date: May 08, 2024 at 10:11 AM
Topic: remotestart, engine doesn’t crank
Posted By: sictruck
Subject: remotestart, engine doesn’t crank
Date Posted: July 05, 2004 at 5:15 PM
Car:2001 s10 truck Alarm: clifford solaris i hooked up the remote start but the engine won't crank. everything goes on, fuel pump, guages etc. i think its because i didn't hook up the 2nd and 3rd ignition wires am i correct? I wasn't sure how or where i need to hook them up. do they splice into the 1st ignition wire or wired up separate to another wire?
Replies:
Posted By: kgerry
Date Posted: July 05, 2004 at 5:28 PM
the must be isolated with relays...did you hook up a Passlock bypass module?
-------------
Kevin Gerry
Certified Electronics Technician
MECP First Class Installer
Owner/Installer
Classic Car Audio
since 1979
Posted By: sictruck
Date Posted: July 05, 2004 at 11:32 PM
yes i hooked up dei555i. can u tell me how to run relays to each? and which wires go to the passlock. this is my first ever install. thanks
Posted By: jaurora
Date Posted: July 06, 2004 at 3:10 PM
The way it sounds it has nothing to do with the passlock. If that were the case the truck would crank but not start. This is the definante issue on the 2nd and 3rd ignition wires. Connect them right in line with the wires.
-------------
MECP certified (If it really means anything)
Jeremy
Posted By: sictruck
Date Posted: July 07, 2004 at 12:33 AM
thanks but i know it has to do with the 2nd and 3rd ignition wires, but i don't know where they go? any help please?
Posted By: jaurora
Date Posted: July 07, 2004 at 6:21 AM
Ignition #1: | | PINK | IGNITION SWITCH HARNESS | Ignition #2: | | PINK/WHITE OR WHITE | IGNITION SWITCH HARNESS (ECM) | Ignition #3: | | N/A | | Accessory: | | ORANGE | IGNITION SWITCH HARNESS (HEAT/AC) |
------------- MECP certified (If it really means anything)
Jeremy
Posted By: sictruck
Date Posted: July 08, 2004 at 12:34 AM
jeremy thanks for the help dude, but i know where and which wires are. I just don't know where those ignitions wire should hook up to the alarm? which alarm wires? thanks chris
Posted By: datrick
Date Posted: July 08, 2004 at 3:24 AM
take the ORANGE / gray wire coming out of the intellistart and attach that to pink/white or white of your ignition2 wire. take the orange wire coming out of the intellistart and attach that to orange wire of your accesory wire I believe your car doesnt have 3rd ignition. So no needs for relay.
Posted By: itmdtr
Date Posted: July 08, 2004 at 5:41 AM
I had this same problem once: It turns out that I had the starter wire from the RS hooked up to the wrong side of the anti-gring (starter kill) relay.  ------------- itmdtr
Posted By: itmdtr
Date Posted: July 08, 2004 at 5:41 AM
I had this same problem once: It turns out that I had the starter wire from the RS hooked up to the wrong side of the anti-grind (starter kill) relay. ------------- itmdtr
Posted By: tanz2004
Date Posted: July 08, 2004 at 4:50 PM
Here is one that most over look. Make sure the Hood is not open when you are trying to start the Car it will not start if you have the Remote Start hooked up right. I have had people call my shop saying that the remote start they installed would not work. Also make sure the wire is not hooked up to Ground. same issue. Hope you get it worked out.
-------------
TanZ2004
Washington State
|