I am planning on installing this security in a 04 Dodge Ram with factory alarm. The owner wanted this alarm because of its features. I have read some of the post about the vehicle and alarm I understand this Ungo is the same as Valet 551r. I have also read some of the post cocnerning this vehicle. I am just trying to gain as much info about alarm and vehicle to avoid any problems. I actually have the vehicle wiring diagram from one post, but I do have a question concerning dome supoervision. What do the mean by use door trigger wire? I would appreciate a wiring diagram. Here is the
link to the old post. Any help is much appreciated. This will be my forth alarm.
-------------
MEH66
"Car Performance and Mobile Electronic Enthusiats"
if youre havin trouble findin the trigger, pretend the dome supervision doesnt exist and just use the door trigger as a "input door trigger".
ur car should have multiple wire for each door, must isolate each wire you grab.
-------------
Houston,TX
"The two most common elements in the universe are H+ and stupidity" (Ellison).
profuse007,
I am confused by your answer. Could you clarify what you meant? Just for clarity, the question I originally asked was pertaining to the wire diagram I got from another post. I copy it below and bolded the question I was trying to clear up in my mind.
04 Ram
12volts red (x2) + ignition harness
Starter yellow + ignition harness
Ignition pink/white + ignition harness
Second Ignition pink/lt. green + ignition harness
Accessory dk. blue & pink/yel (16 awg) + ignition harness
Second Accessory pink / YELLOW (14 awg) + ignition harness
Power Lock PURPLE / dk. green - driver kick, door harness
Notes: Lock is negative trigger thru an 820 ohm resistor. Unlock is negative trigger thru a 330 ohm resistor. MUST use relays.
Power Unlock same wire as power lock
Parking Lights+ wht/yel (L), wht/gray (R) + harness at top of driver fender
Parking Lights- WHITE/ lt. green - headlight switch
Notes: Parking lights are negative trigger thru a 249 or 330 ohm resistor. MUST use a relay.
Door Trigger see notes - see notes
Notes: The driver door trigger is purple and the driver side rear door is PURPLE / orange. These wires are in the driver kick panel. The passenger door trigger is PURPLE / white and the passenger side rear door is purple / YELLOW. These wires are in the passenger kick panel. Use all four wires and diode isolate each. See DirectFax document 1076 for wiring information.
Dome Supervision use door trigger wire
Factory Alarm Arm PURPLE / lt. blue - driver kick, door harness
Notes: This will also do door locks. Arm/lock is negative trigger thru a 2K ohm resistor. Disarm/unlock is negative trigger thru a 480 ohm resistor. Single pulse will do disarm without unlocking the doors. Unlock requires a double pulse. MUST use relays.
Factory Alarm Disarm same wire as factory alarm arm
Tachometer dk. blue/gray ac PCM, orange plug, pin 34
Notes: The PCM is on the passenger side firewall. On diesel models the tach wire is at the ECM on the lower driver side of the engine, 60 pin plug, pin 24.
Wait to start see document 1091
Brake Wire WHITE/ tan + brake pedal switch
Parking Brake dk. GREEN / WHITE - parking brake switch
Horn Trigger dk. GREEN/ purple - steering column
Immobilizer Bypass Module: Required: Yes Type: Sentry Key Part #: 555C or 555U
Notes: Only vehicles with gray keys have the immobilizer.
-------------
MEH66
"Car Performance and Mobile Electronic Enthusiats"
Hey man thanks for the info i did one yesterday and the only problem i had was that i got a wiring diagram from a post i found yesterday and all the wire colors where wrong so i had to find all the wire colors myself it was a **** but the colors you put up are the exact ones i found i put a regular alrm the only problem was the dome light wire. Because you need to diode isolate but other than that i had no problem keep in mind i put a regular alarm not remote start. If read about alot of problems other installers have had with remote start but i think as long as you do everything the way its suppose to be done you should not have any problem just make sure to diode isolate any wires your suppose to and dont pick on any wires your not suppose to.
-------------
WiredUp