1999 honda accord parking lights
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=38303
Printed Date: July 16, 2025 at 7:03 AM
Topic: 1999 honda accord parking lights
Posted By: raskal
Subject: 1999 honda accord parking lights
Date Posted: August 29, 2004 at 8:28 PM
I have a 1999 honda accord and recently put keyless entry on it now i am trying to hook up the flashing parking lights but when i tap into the RED / black wire for the parking lights from the relay i get nothing from it and i am completely lost as to what could be the problem. any help would be appreciated. thanks in advance.
Replies:
Posted By: profuse007
Date Posted: August 29, 2004 at 8:37 PM
alarm model?
-------------
Houston,TX
"The two most common elements in the universe are H+ and stupidity" (Ellison).
Posted By: mo12v
Date Posted: August 29, 2004 at 8:40 PM
| Parking Lamp | RED / BLACK (+) | GREEN 20 PIN CONN. DRIVER FUSE BLOCK |
If you are using a Scotch-lok type tap, check to make sure you are peircing the wire. Have you put a meter on the RED / BLACK to see if you are getting voltage? With the Parking Light switch and from the Keyless Entry ------------- MO
Don't Learn from Others Mistakes
You Might Be the One That Knows.
Posted By: auex
Date Posted: August 29, 2004 at 8:48 PM
I agree, need the alarm info. Some alarms only put out a negative trigger and you may need a relay.
-------------
Certified Security Specialist
Always check info with a digital multimeter.
I promise to be good.
Tell Darwin I sent you.
I've been sick lately, sorry I won't be on much.
Posted By: raskal
Date Posted: August 31, 2004 at 7:07 PM
I have a question about a relay i am trying to hook up my keyless entry to my parking lights and when every i hook the wire up to the parking lights wire all i get is buzzing., but when the wire is not hooked up it works fine. it is a 30 amp relay. any help would be greatly appreciated. thanks
Posted By: another-kelly
Date Posted: August 31, 2004 at 7:44 PM
MORE INFO! what wires are going to the relay (i.e.-#30 to vehicle parking lights, #87 to constant 12V)? what make/model alarm?
Posted By: raskal
Date Posted: August 31, 2004 at 8:06 PM
it is a bulldog security ke100. the wire from the system is to #86, to parking lights #87 and 20 amp fused 12v constant to #30 and #85
Posted By: slipkx2
Date Posted: September 01, 2004 at 1:10 PM
in my civic it was green with a red strip or vise versa in the ignition harness dont know if its the same. make sure to test before you strip.
Posted By: another-kelly
Date Posted: September 01, 2004 at 5:46 PM
can't find a diagram for it. is the parking light output from the alarm + or - signal? also, have you metered the parking light output from the brain to make sure it's putting out?
Posted By: xtremeaudio
Date Posted: September 03, 2004 at 2:06 AM
ON MOST ALARM PARKING LIGHT WIRE WILL WHITE (+) CHECK FROM ALARM WHAT YOU HAVE (-) OR (+) IF YOU HAVE (+) GO DIRECT TO RED / BLACK IF YOU (-) THEN YOU NEED RELAY 86 AND 87 GO TO (+) 30 GO TO RED / BLACK AND 85 GO ALARM (87A IS NO USE )
Posted By: dBDevil
Date Posted: September 04, 2004 at 12:41 AM
Don't waste time trying to find the individual wire. You can get the parking lights directly from a small male spade connector on the fuse box. Test with a multimeter. There are about 5-7 of those connectors, use for the factory security. Test, then use a female spade on the 12v+ parking light output on the alarm.
|