VIper 791 remote start program help
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=39312
Printed Date: July 07, 2025 at 11:08 AM
Topic: VIper 791 remote start program help
Posted By: jeep thang
Subject: VIper 791 remote start program help
Date Posted: September 18, 2004 at 1:46 AM
Hello, New to forum, Need ass-istance........
my problem.... I cant seem to fiqure out how to program the remote start correctly...
I have all wiring done correctly for the remote start, so this is a programming problem
When i hit the remote start button on the lcd pad,, nothing happens..
can someone walk me through a easy way to program the remote start?
Replies:
Posted By: xtremeaudio
Date Posted: September 18, 2004 at 2:53 AM
open any door turn key and off press and hold valet swith in still you 3 beep and press on valet 2 time and hold and you hear 2 beep and press unlock button on remote you will hear 2 beep now you done turn on and off again
Posted By: jeep thang
Date Posted: September 18, 2004 at 10:57 AM
Yes thank you,,, Now when i hit the remote start button, it will make some clicks in the viper remote start and the tach will come on,,, but it doesnt start to crank over or anything.... did i program wrong?
Posted By: jeep thang
Date Posted: September 18, 2004 at 11:12 AM
Now i can get it to start,, but it shuts off immidiently after it starts....what should i check?
Posted By: jeep thang
Date Posted: September 18, 2004 at 11:41 AM
Okay ,,, getting farther and farther on it now,,,, If i have the key in the ignition on acc.... and hit the start button, it starts,, but then the starter grinds out... i have a green wire comming from the viper alarm that isnt going to anything, and its supposed to goto the Key side ignition wire on my jeep wrangler...... i cant find the color of that wire :(... some one help please
Posted By: profuse007
Date Posted: September 18, 2004 at 2:10 PM
first try to learn the tach again, if it still does it try using another tach source.
what year model?
-------------
Houston,TX
"The two most common elements in the universe are H+ and stupidity" (Ellison).
Posted By: jeep thang
Date Posted: September 18, 2004 at 3:07 PM
1997 jeep wrangler... sahara edition
I tried fallowing the persons directions up top to learn the tach and it didnt work
It will start for 1 second then shut off, so i assume its something with the tach and voltage correct???
Posted By: jeep thang
Date Posted: September 18, 2004 at 6:59 PM
I found a good tach source,, but now when i start, it runs for 10 seconds,, then shuts off... i read in back of manual try to do a low voltage start??? how do i do that? what can i do if it only runs for 10 seconds?
Posted By: xtremeaudio
Date Posted: September 19, 2004 at 2:39 AM
ok let try this use tach less open any door turn key and off press and hold valet swith in still you 3 beep and press on valet 2 time and hold and you hear 2 beep and press unlock button on remote you will hear 2 beep then press 3 time on valet swith and one more and hold it press unlock button one time you hear 2 beep press one more time you hear 3 beep now turn key on and off you done i hope this work for you at the mean time check 2 green fuses on the big wire harness |
Posted By: peanut36274
Date Posted: September 29, 2004 at 11:40 PM
I have a 2003 Jeep wrangler and it does the same thing. It start and then shuts off. Where is the tach wire because I couldn't find one on mine. couldn't find the coils
Posted By: jeep thang
Date Posted: September 30, 2004 at 1:28 AM
i found the take wire.. take off the gauge cluster and its a grey wire,, well atleast for my year it was... very easy to take off the cluster,, and it plugs right into the back of it..
|