Alarm install 94 4runner
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=39771
Printed Date: July 05, 2025 at 11:35 PM
Topic: Alarm install 94 4runner
Posted By: Prophit
Subject: Alarm install 94 4runner
Date Posted: September 26, 2004 at 1:32 PM
Im about to start installing my alarm into my 4runner and wanted to ask if the factory alarm will need to be either disabled or uninstalled? I found the module underneith my seat. Im thinking i can use alot of those wires to tap into for the install. Also im a little confused on the starter kill I have an fm2009 alarm and it already was wired into a car. So there are some relays already but im not quite sure i know what im doing. If someone could just help me with the wiring i would be ready to go. 1994 4 runner FM 2009 Alarm with remote start. Please help!!
Replies:
Posted By: Prophit
Date Posted: September 26, 2004 at 9:02 PM
About to finish my install on my 4runner and just doing some research on either to go tachless or install the tach cable. The directions i have found tell me its a black cable at the diags box. I checked and its inside of like 2 differect heat shrink covers. I can take that off but is it worth it? Please assist. Thanks
Posted By: Teken
Date Posted: September 26, 2004 at 9:05 PM
Tach is the only tried and true method to ensure a consistent RS, each time.
Regards
EVIL Teken . . .
Posted By: snguyen
Date Posted: September 26, 2004 at 9:12 PM
Posted By: Prophit
Date Posted: September 26, 2004 at 10:42 PM
Ok well then where should i tap in at.. Should I couse a coil? or go in where the distribtor is?But going through where the wiring diagram says is hard.
Posted By: Prophit
Date Posted: September 27, 2004 at 10:10 AM
Got my alarm finally installed but i have noticed that the siren is not working. I took this alarm out of another car that i didnt install. I found that they are using a relay for the siren. Is that needed? Its an fm2009 alarm. Please help. Thanks
Posted By: Velocity Motors
Date Posted: September 27, 2004 at 10:27 AM
Probably used relays because it had more than a couple of sirens hooked up to the siren wire. Check the output of the siren wire to see if your getting a current from it.
-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Posted By: Prophit
Date Posted: September 27, 2004 at 10:45 AM
Ya there was 2 sirens hooked up but im only using one. I will check that later. If i just use the one do i need to use relays?
Posted By: Velocity Motors
Date Posted: September 27, 2004 at 10:58 AM
If you just use one, then you don't need a relay.
-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Posted By: Prophit
Date Posted: September 27, 2004 at 12:44 PM
So i have a 94 4 runner. Directions say to use the black cable at the diags box. Well that cant be done. So whats another place to do this at? Maybe at the distriboter or something?
Posted By: mo12v
Date Posted: September 27, 2004 at 12:46 PM
| Tach Signal | BLACK | AT IGNITER OR DIAGNOSTIC PLUG * |
* Igniter Located On Driver Firewall, Diagnostic Plug Located On Passenger Side Of Engine Compartment On Fuse/Relay Box. BLACK Tach Wire Also Found At Pin #20 In A White 20 Pin Connector In Passenger Kick Panel. ------------- MO
Don't Learn from Others Mistakes
You Might Be the One That Knows.
Posted By: Prophit
Date Posted: September 27, 2004 at 12:55 PM
sweet thanks man i will take a look tonight.
|