Civic and Prelude
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=4034
Printed Date: July 18, 2025 at 8:40 PM
Topic: Civic and Prelude
Posted By: LudeBoi
Subject: Civic and Prelude
Date Posted: September 28, 2002 at 11:35 PM
I am a new proud member, just passed by and whoa.. this site rocks, has ALOT of info, well anyway any one know the wire colors for the windows on a 95 Civic an a 98 Prelude? thanks
Replies:
Posted By: SOUND PRESSURE
Date Posted: September 29, 2002 at 12:00 AM
95 honda civic= windows up LF-RED / blue, RF-blue / YELLOW windows down=LF-RED / yellow, RF-blue/green 98 honda prelude= | Windows Up | LF=RED / Blue, RF=Blue / YELLOW in Door only | | Windows Down | LF=RED / White, RF=Blue |
------------- Sound Pressure
You know you have the right amount of pressure when your eyes start to water! Now you've got Juice!
Posted By: LudeBoi
Date Posted: September 29, 2002 at 5:28 PM
thanks,i installed the window modulator today and it doesnt work!!...grr...pissing me off, i made sure all the wires were correct, i was thinkin b/c my alarm aux output only puts out 300ma and the window modulator is 500ma? if not wats the problem? thanks in advance
Posted By: Velocity Motors
Date Posted: September 30, 2002 at 5:22 AM
Are you using the proper trigger wires for the module ? Sometimes the modules have a trigger and an AUX wire to other devices ( this is a output not input ). ------------- Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Posted By: LudeBoi
Date Posted: September 30, 2002 at 8:06 AM
Thanks for replying, Im not quite sure what your talking about, but the module has 8 wires: 2 for each window 1ground 112volt 1 500ma ACTIVATION? 1 pink accessory wire? I have the Prestige aps-25kb alarm, am I supposed to hook up the activation wire from the module to the blue aux wire of the alarm? or is a relay needed? thanks alot
Posted By: Mobile Ins
Date Posted: September 30, 2002 at 9:10 AM
Hi all..i'm new to this site but i'm trying my best ..i'm form Canada,Ontario and working as Master/Installer make sure you wires not wrong and after cuting driver door window up wire you need to remember which side going to motor and switch if it's not right window won't work..also from APS-25 you have to connect Orange wire but if you using this wire for starter disable it won't work on window module and you need diodes to aviod ground coming from starter kill realy. the module you using it's just for one function either window down or up.. Pink wire don't need to connect..it's out put for some accessory ------------- Mobile Installer
Posted By: LudeBoi
Date Posted: September 30, 2002 at 4:45 PM
yeah im trying to make both windows go up when i push the little green button (aux 2), yes i am using the orange wire for starter disable, so im supposed to use the blue wire and simply connect it to the activation wire of the module rite? John
Posted By: Velocity Motors
Date Posted: September 30, 2002 at 9:31 PM
What is your activation wire timed out for ( BLUE ) ? The activation wire will only roll down the window for as long as there is current in the trigger wire. If you hook up the starter disable ( to close the windows upon arming the system ) then attach the starter disable wire to the activation wire on the module. This wire will stay active for as long as the car is armed, but don't worry because the window modules have an automatic current spike regulator that monitors current spikes and shuts off power when the windows are fully closed.
-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Posted By: LudeBoi
Date Posted: October 01, 2002 at 2:29 PM
thanks, i hope this works!! John
Posted By: LudeBoi
Date Posted: October 01, 2002 at 4:06 PM
it works.. but it makes the windows go up instantly after i take out my key out of the ignition..but i found the problem of the whole thing! it was a faulty aux button on the remote!, but now i came across another problem, i connected the activation wire to the aux output and it works, but i'll have to press the aux button a few times, because it goes up and stop, so i have to keep pushing the aux button to get it to completely rolled up?!?
Posted By: Velocity Motors
Date Posted: October 01, 2002 at 9:08 PM
That's because of what I had asked in the previous post.... What is your activation wire timed out for . The remote modules will only activate for as long as there is current in the wire. You will need to find a latched or a continuous output channel to make the windows roll down all the way without having to press the button more than once. ------------- Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Posted By: LudeBoi
Date Posted: October 02, 2002 at 9:48 AM
Oh, what exactly do you mean by activtion wire timed out for? thanks John
Posted By: mobiletoys2002
Date Posted: October 02, 2002 at 2:05 PM
use a wire off the alarm that has a constant output when you press the button like aux ... for instance an output that is latched reset with ignition will work... this means the output will stay on the wire until you turn on th eignition or press the aux button again whichever is first. Velocity said to wire the module so it has a constant trigger so the windows will roll up the first time without pressing buttons more than once.Ok last thing activation timed out for means how long the activation wire is set to supply voltage if it shuts off to soon the window will not roll up all the way and a second press of the button will be required, a latched will stay on supling voltage all the time for a preset time or until an action by you is done like turning ignition,etc read your owners manual or install manual to see what that wire can do .
|