Print Page | Close Window |
Alarm + Remote Start in 99 Toyota 4RunnerPrinted From: the12volt.comForum Name: Car Security and Convenience Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc. URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=40706 Printed Date: May 08, 2024 at 11:02 PM Topic: Alarm + Remote Start in 99 Toyota 4Runner Posted By: Robacarp Subject: Alarm + Remote Start in 99 Toyota 4Runner Date Posted: October 11, 2004 at 8:06 PM Hello, I am going to be installing an alarm and remote start in a friends 1999 Toyota 4Runner, and I cant for the life of me seem to find any websites that can give me the install info that I need for the car. If this is unclear what I mean, I mean that I cant find the wire locations for the locks, lights, ect. I could find them on my own, but sometimes that can be really frustrating and annoying. So, does anyone know of a website where I can get that info (or even better, does anyone have that info they could email me?)\ Thanks. ------------- Robert Carpenter Replies: Posted By: Teken Date Posted: October 11, 2004 at 9:17 PM Toyota 4-Runner 1999-2002 Remote Starter Wiring Colors and Notes Function Vehicle Color Location Start: GREEN/ BLACK IGNITION SWITCH HARNESS * Ignition #1: BLACK/ RED IGNITION SWITCH HARNESS Ignition #2: BLACK / YELLOW IGNITION SWITCH HARNESS Ignition #3: N/A Accessory: BLUE/RED IGNITION SWITCH HARNESS Brake Light: GREEN / WHITE (+) AT SWITCH ABOVE BRAKE PEDAL Tach Signal: BLACK AT IGNITER ON PASS. WHEELWELL ** Parking Lights: RED / GREEN (-) AT ALARM MODULE Headlights: RED (-) AT HEADLIGHT SWITCH *** OEM Alarm Disarm: YELLOW/RED (-) Key Sense Wire Found Below Steering Column**** OEM Alarm Arm: BLACK / YELLOW (+) AT ALARM MODULE Diesel Glow Plug: Clutch Bypass Wire: Notes: * 2000 Vehicles May Be Equipped With a Transponder Type ** BLACK Tach Wire Also Found In Data Link Connector On Driver Side Of Engine (4 Cyld.) Or At Engine Control Module Located Behind Pass. Dash (6 Cyld.) Or Can Also Be Found In 26 Pin Connector In Pass. Kick Panel On Both. -------------------------------------------------------------------------------- Toyota 4-Runner 1999-2002 Alarm and Keyless Entry Wiring Colors and Notes Function Vehicle Color Location Constant +12 Volts: WHITE/ RED & WHITE IGNITION SWITCH HARNESS Starter Kill: GREEN/ BLACK IGNITION SWITCH HARNESS * Ignition +12 Volts: BLACK/ RED IGNITION SWITCH HARNESS Dome Lights/Superv: GREEN/ BLACK (-) AT DOME LIGHT OEM Horn: GREEN/ RED (-) AT ALARM MODULE Power Lock: RED / WHITE (-) WHITE CONN. ABOVE BLUE IN DR. KICK*** Power Unlock: RED (-) WHITE CONN. ABOVE BLUE IN DR. KICK*** Trunk Release: Alarm Input Wire: GREEN/ BLACK (-) AT DOME LIGHT Notes: ** Fuse Block Located In Driver Dash. *** Child Safety Locks: RED / BLUE (-) In Same Conn. As Door Lock Wires Above. See Note #209 - See Child Safety Locks Diagram. Lock Wires Are Also Found At Alarm Module. Lock BROWN / White (-) Unlock GREEN/ YELLOW (-. **** Use Ignition 3; Negative Out While Running. Posted By: Teken Date Posted: October 11, 2004 at 9:19 PM 12volts white - WHITE/ red + ignition harness Starter GREEN/ black or black + ignition harness Second Starter Ignition BLACK / YELLOW + ignition harness Second Ignition blk/red + ignition harness Third Ignition Accessory blue/red + ignition harness Second Accessory Keysense Power Lock BROWN / white - plug below fuse box Notes: The door lock wires will meter while turning the key in the passenger door key cylinder. Power Unlock grn/yel & blu/yel - plug below fuse box Notes: The door lock wires will meter while turning the key in the passenger door key cylinder. The GREEN/ YELLOW wire is the key cylinder unlock wire, the blue / YELLOW wire is the unlock detection wire. Use both wires and diode isolate. Lock Motor blue/white driver kick blue 12 pin plug Unlock Motor pink/green driver kick blue 12 pin plug Parking Lights+ green dimmer or harness to rear Parking Lights- RED / white light switch or column Hazards Turn Signal(L) Turn Signal(R) Reverse Light Door Trigger lt. GREEN/ black - Notes: behind drivers side junction block in a 13 pin plug. Dome Supervision use door trigger - Trunk/Hatch Pin tied in with door - Hood Pin GREEN/ orange - Notes: drivers side firewall in a gray 26 pin plug. Trunk/Hatch Release Power Sliding Door Factory Alarm Arm arms with lock Factory Alarm Disarm disarms with unlock Disarm No Unlock yellow/red - steering column Notes: This is the ignition key sense wire. Using the status output wire from the remote start to ground this wire will disarm the alarm without unlocking the doors. Tachometer black Notes: located in the diagnostic plug on the drivers side of engine compartment. Wait to start Brake Wire GREEN / WHITE + at switch Parking Brake Horn Trigger GREEN/ red - steering column Memory Seat 1 Memory Seat 2 Memory Seat 3 Immobilizer Bypass Module: Required: Yes Type: Transponder Part #: 555X, 556U, or 555U Notes: N/A This wiring information is being provided free of charge on an "as is" basis, without any representation or warranty. It is your responsibility to verify any circuit before interfacing with it using a digital multimeter. Posted By: Teken Date Posted: October 11, 2004 at 9:21 PM Toyota 4Runner 1999 Remote start / Security / GPS Wire/Function Colour Location/Description Polarity PASSIVE ANTI-THEFT YES TRANSPONDER SEE NOTES 12 VOLTS White or WHITE/ red Ignition harness + IGNITION BLACK / YELLOW Ignition harness + IGNITION 2 BLACK/ red Ignition harness + ACCESSORY Runs with ignition Ignition harness + STARTER GREEN/ black Ignition harness + TACH See notes* LOCK BROWN / white In driver's kickpanel - UNLOCK Blue/black & RED / blue** In driver's kickpanel - DOORPIN SEE NOTES*** TRUNK PIN Lt.GREEN/ red In driver's kickpanel - TRUNK RELEASE Manual release FACTORY ARM Arms with lock wire FACTORY DISARM Disarms with unlock wires BRAKESWITCH GREEN / WHITE At switch above brake pedal + PARKLIGHTS Green At light switch harness + HAND BRAKE RED / white At plug on handbrake lever - HORN GREEN/ red At steering column - CLUTCH SWITCH BLACK/ white At switch on clutch pedal TYPE 1 DRIVER WINDOW UP Lt.green At main window switch REV POL DRIVER WINDOW DOWN Blue / YELLOW At main window switch REV POL PASSENGER WINDOW UP RED / black At main window switch REV POL PASSENGER WINDOW DOWN RED / green At main window switch REV POL LEFT REAR WINDOW UP RED / blue At main window switch REV POL LEFT REAR WINDOW DOWN RED / yellow At main window switch REV POL RIGHT REAR WINDOW UP Yellow At main window switch REV POL RIGHT REAR WINDOW DOWN Green At main window switch REV POL HEADLIGHTS RED / yellow At light switch harness - REVERSE LIGHTS RED / white In driver's kickpanel + DIMMER WHITE/ green At dimmer switch harness VSS WIRE GREEN/ orange**** At ECM behind glove box**** KEY SENSE Yellow/red Ignition harness - Vehicle notes PLEASE NOTE: This vehicle may be equipped with a IMMOBILIZER passive anti-theft system. Please refer to our security diagram before installing any remote start products. * On the 2.7L engine there are 2 coils on the right front of the engine. Use the BLACK/ RED or BLACK/ BLUE for a 2 cylinder signal. On the 3.4L, the tach is BLACK at the igniter on the right side of the engine (6 cylinder signal). You can also find a tach reference at the ECM module behind the glovebox. On the 2.7L, BLACK at pin-15 of the 26-pin connector. ** Both these wires must be connected and isolated with 2 IN4001 diodes. This will require 2 pulses to unlock the doors. *** Doorpins are independent. Driver's door is BLACK in driver's kickpanel, rear doors are BLACK/ RED in driver's kick and BLACK/ WHITE is passenger door on back of fuse panel. **** The GREEN/ ORANGE vss wire is located at the ECM behind the glovebox. On the 2.7L, pin-8 of the 22-pin connector. On the 3.4L, pin-22 of the 28-pin connector. Note: The information on this sheet is provided to you on an as is basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. Wiremagic.com Corporation and/or any associated or unassociated individual or corporation who furnishes this document and/or software assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in each and every case is the sole responsibility of the installer performing the work and Wiremagic.com Corporation and/or any associated or unassociated individual or corporation assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly, or in any other way. The information supplied is a guide only. -------------------------------------------------------------------------------- ©2002 Autoland All rights reserved Printed at: 10/11/2004 10:18:57 PM Posted By: Teken Date Posted: October 11, 2004 at 9:22 PM WIRE COLORS LOCATION 12 VOLTS CONSTANT WHT OR WHT/RED IGNITON SWITCH HARNESS IGNITION 1 BLK/YEL IGNITION SWITCH HARNESS IGNITION 2 BLK/RED IGNITON SWITCH HARNESS IGNITION 3 N/A N/A ACCESSORY /HEATER BLOWER 1 BLU/RED IGNITON SWITCH HARNESS ACCESSORY /HEATER BLOWER 2 N/A STARTER GRN/BLK OR GRN IGNITION SWITCH HARNESS PARKING LIGHTS GRN (+) AT LIGHT SWITCH DOMELIGHT BLK(dr) BLK/RED (rear) DR KICK PANEL PWR DOOR LOCK BRN/WHT (-) DR KICK PANEL PWR DOOR UNLOCK RED (-) & RED / WHT TYPE B *SEE DIAGRAM* TRUNK RELEASE N/A N/A TACH SENSOR BLK AT DIAG CONNNOR IGNITOR (PASS FENDER) BRAKE GRN/WHT (+) SWITCH ABOVE BRAKE PEDAL HORN N/A N/A FACTORY DISARM W/LOCKS N/A N/A N/A Posted By: Robacarp Date Posted: October 14, 2004 at 7:38 PM holy cow. Can I ask where you people get this info? ------------- Robert Carpenter Posted By: mo12v Date Posted: October 14, 2004 at 7:44 PM This one to:
Reversal Rest At Ground Power Window Circuit
Immobilizer Bypass Circuit ------------- MO Don't Learn from Others Mistakes You Might Be the One That Knows. Posted By: Teken Date Posted: October 14, 2004 at 9:58 PM Robacarp wrote: ASAP requests are all copy and pasted from various internet security sites. Actual PDF form schematics are sent via e-mail upon the users request(s), if they wish to view them in their original form. As always the information provided is simply a guide. It is not intended to replace the varification of the contact points without the use of a DMM, and one good working brain. P.S. You will find that mo12v will always supply you with a better *looking* wiring form. Just because he has to make me look bad !! [:o] Regards EVIL Teken . . . Posted By: mo12v Date Posted: October 14, 2004 at 10:01 PM That's NOT true.............I like your B & W presentation better.......It's easier on the eye's
------------- MO Don't Learn from Others Mistakes You Might Be the One That Knows. Posted By: Robacarp Date Posted: October 15, 2004 at 9:56 AM Yea, the only thing that I makes me think about the internet security sites is that I couldnt find any that would give the information for free....they all wanted me to pay ...... Thanks everyone ------------- Robert Carpenter |
Print Page | Close Window |