04 Sienna unlock wire

Hello,

I try to install the Compustar 2WAS module (CM3000) into 04 Toyota Sienna. The problem I have right now is , I can't locate the power Unlock wire. According to wiring diagram is BLUE, but it shows 0V at all time even when I rotate the key from LOCK to UNLOCK . I did find the power lock wire . It is LIGHT GREEN.

Does anyone experiences , Idea , Opinions. Please help me to locate this wire

THANK YOU

By the way, The accessories wire is BLACK / YELLOW( small wire) NOT PINK as the wiring diagram says

Could someone please comfirm it ?

-------------
Autostar

You may also use the passenger door key cylinder wire for unlock. Wihich only requires a single pulse. It is blue / YELLOW (-) and can be located in the passenger kick in a 12 pin plug.

Regards

EVIL Teken . . .

Sorry U R having difficulties, but not knowing how U wired your unit, I must have been making this mistake on ALL the Toyotas I have done.......Yeah right

As for your UNLock issue:  read note at bottom and try to understand

Ignition #2	BLACK / YELLOW 18 GAGE	IGNITION SWITCH HARNESS
Ignition #3
Accessory	PINK	IGNITION SWITCH HARNESS

NOTE **    These 2 wires will ONLY meter (show a Ground or (-) Negative) when you place a key in the DRIVERS DOOR KEY CYLINDER (outside of drivers door) and rotating from Lock to Unlock. You must use a Double Pulse Unlock programming on this vehicle. For a Single Pulse Unlock you can use the wire in the Passengers kick panel in a 12 Pin Plug, it will meter off of the Passengers key cylinder, the wire is a BLUE / YELLOW (-).

-------------
MO

Don't Learn from Others Mistakes
You Might Be the One That Knows.

Hi mo12V,

I'm really sorry for what I have said . I'm too new to this field. Please forgive me. what I meant is : I really don't know what the Ignition #2 mean . When I connected the PINK to accessory from module I didn't get the fan blow. But when I connect BLACK / YELLOW 18 GAGE to Accessory I got fan blow. I thought there is a mistake.

I have read the NOTE ** many many times and my understand is : I must have 12V at BLUE wire before trigger. When I place a key in the DRIVERS DOOR KEY CYLINDER (outside of drivers door) and rotating from Lock to Unlock. I must see a pulse Ground or (-) Negative. Please point me to the right direction if I'm wrong

-------------
Autostar

If U have found the Lock wire in the Connector in Driver Kick Panel, the BLUE UNLock wire should also be there.
Have U tried a direct ground "touch" to the L/GREEN or BLUE wire to see if they respond?

Power Lock	L GREEN	DRIVERS KICK WHT 18 PIN CONN
Power Unlock	BLUE	DRIVERS KICK WHT 18 PIN CONN

You must use a Double Pulse Unlock if using BLUE wire

For a Single Pulse Unlock you can use the wire in the Passengers kick panel in a 12 Pin Plug, it will meter off of the Passengers key cylinder, the wire is a BLUE / YELLOW (-).

-------------
MO

Don't Learn from Others Mistakes
You Might Be the One That Knows.

Thanks Man

 I'll will try that

-------------
Autostar

the lock/unlock wires are at the driver kickpanel

Hi,

Let me explain what I have done :

The Light Green ( Lock ) connect to module . It's working good ( It's about 10V at rest and pulse to ground when trigger )

The Blue ( Unlock ) at driver kick and the Blue / YELLOW at passenger kick. They are both show 0V at all time. Trigger them to ground nothing happen

I did probe almost every single wire in driver & passenger kick to locate the unlock wire but still no luck

My next step is to open driver door panel to get the wire.

Any idea would be appreciated?

Thank You

-------------
Autostar