94 Camry Alarm/Remote Start

Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=46393
Printed Date: May 03, 2024 at 6:57 AM

Topic: 94 Camry Alarm/Remote Start

Posted By: karma
Subject: 94 Camry Alarm/Remote Start
Date Posted: December 30, 2004 at 2:47 PM

Where can i find the diagram to setup remote start on a 1994 Toyota Camry Coupe using a Viper 790VX alarm and remote start module?

Replies:

Posted By: snguyen
Date Posted: December 30, 2004 at 2:51 PM

Toyota

Camry

1994-1996

Remote Starter Wiring Colors and Notes
Function	Vehicle Color	Location
Start:	BLACK/ WHITE	IGNITION SWITCH HARNESS
Ignition #1:	BLACK/ ORANGE	IGNITION SWITCH HARNESS
Ignition #2:	BLACK / YELLOW	IGNITION SWITCH HARNESS
Ignition #3:	N/A
Accessory:	PINK/BLUE	IGNITION SWITCH HARNESS
Brake Light:	GREEN / WHITE	(+) AT SWITCH ABOVE BRAKE PEDAL
Tach Signal:	BLACK	AT DIAGNOSTIC CONNECTOR *
Parking Lights:	GREEN (+)	AT FUSE/JUNCTION BLOCK ('TAIL'FUSE)
Headlights:	RED / YELLOW	(-) AT HEADLIGHT SWITCH
Diesel Glow Plug:
Clutch Bypass Wire:
Notes:	* Diagnostic Connector Located On Passenger Rear Of Engine Compartment. 6 Cylinder Engine- BLACK Tach Wire Located On Driver Strut Tower.

Toyota

Camry

1994-1996

Alarm and Keyless Entry Wiring Colors and Notes
Function	Vehicle Color	Location
Constant +12 Volts:	WHITE AND WHITE/ RED	IGNITION SWITCH HARNESS
OEM Alarm Disarm:	N/A
Dome Lights/Superv:	RED / WHITE (-)	FUSE/RELAY BLOCK - DRIVER KICK PANEL
OEM Horn:	GREEN/ BLACK	(-) STEERING COLUMN HARNESS
Power Lock:	LIGHT GREEN	BLUE # PIN CONN. IN DRIVER'S KICK **
Power Unlock:	DARK GREEN	BLUE # PIN CONN. IN DRIVER'S KICK **
Trunk Release:	BLUE/BLACK (+) # PIN	CONN.DRV KICK (WAGON ONLY)
Alarm Input Wire:	RED / WHITE (-)	FUSE/RELAY BLOCK - DRIVER KICK PANEL
Notes:	** Child Safety Locks- BLUE/RED At Pin #9 In Same Connector As Door Lock Wires Above. See Note #209 - Child Safety Door Lock Diagram.

Posted By: karma
Date Posted: January 12, 2005 at 2:18 PM

Ok i have a question. On the drivers side kick panel is the RED / white wire that cnotrols the dome light. Which plug is it on. I saw 3 different wires on there and when i unplugged each plug they didn't turn off the dome light.

Also how do i hook it up so that my 790vx turns on my dome light when i unlock the doors? how do i hook a relay to it? do i splice it?

Posted By: Jschult3
Date Posted: January 12, 2005 at 4:11 PM

Check out the section on this site that talks about relay's. The diagram below is for Neg door triggers. If you have positive triggers pin 87 gets tied to pin 85 instead of ground.

posted_image

-------------
Jeff
Always Verify Wire information before Connecting! Just a Darn Good DIY'R

Posted By: karma
Date Posted: January 12, 2005 at 5:56 PM

I'm trying to hook up Remote Start in my 94 Camry and i have a question. I'm using the 790vx Viper alarm and the proper remote start modules for the install. I'm confused about placement of a couple wires when it comes to the Remote Start.

1) On ignition 1, if i place the wire that detescts voltage for Zone 5 (ignition) protection on this circuit, do i have to place the ignition power wire from the Remote start relay further away from the lock solenoid(more down stream)?

2) If i do have to put it further down stream, do i have to put a diode in line on the Ignition wire to keep power from going backwards up the sensor wire and cycling back in to the alarm or does it matter?

3) Does the ignition sensor wire and remote start ignition output wire have to be further down than the ignition wire i have hooked up to the Failsafe starter kill relay? Like so....

Key switch]-----X---------------------------------------X----------------------------------------X-->Ignition1

StarterKill Sensor Rte Start

Thanx

Posted By: karma
Date Posted: January 12, 2005 at 6:02 PM

Also, i forgot, Do i have to place a diode inline with my starter kill relay ouput so that the current doesn't go backwards when i activate my Remote start and electricity runs from the starter output relay and in to the same wire the starter kill is hooked up to?

Posted By: karma
Date Posted: January 12, 2005 at 7:03 PM

If i do it like that won't it show as the doors being open and set off Zone 3 in my alarm. I just want to set it up to turn on my dome light not just trigger the door to think it's open and turn on the dome.

Posted By: Jschult3
Date Posted: January 13, 2005 at 11:40 AM

1) NO- should not need to as long it's connected.

2)NOPE

3)WHat do you mean about being further downstream, are you referring to the key sense wire?

No diodes needed unless your paranoid. Do you have the install manual for the 790xv? It should be very specific about where you need to place any diodes. The only time you need a diode in starter kill with this alarm is if your using a window module which is also connected to the orange wire as is the starter kill.

-------------
Jeff
Always Verify Wire information before Connecting! Just a Darn Good DIY'R

Posted By: CutDog504
Date Posted: January 13, 2005 at 11:27 PM

About the "RED / white" wire you mentioned for the door trigger... Most toyotas have several RED / whit wires in the kick panel. You have to probe them and find out which is the right one. Also, one of those RED / white wires is the trunk trigger. Connect it to the blue wire on your alarm and it will trigger your alarm if anyone opens your trunk.