2003 chevy venture Remote starter
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=46946
Printed Date: May 17, 2024 at 7:18 PM
Topic: 2003 chevy venture Remote starter
Posted By: firefighter321
Subject: 2003 chevy venture Remote starter
Date Posted: January 05, 2005 at 12:21 AM
I am putting in a remote starter alarm in 2003 chevy venture. I cant seem to get the starter to work the remote is the x-plore xr-7025. The way the directions read is connect the green wire to air condition and the other green to the keyhole on wire. Is the key hole on wire the ignition 1 wire?. Gray wire start engin wire. Is this ignition2 wire? they have a relay which states Gray wire connects to start wire to 87a on the relay. 30 on the relay to start motor to wire they say cut, is this the yellow starter wire? and the Green wire to key hole to 86 on the relay. and 85 to yellow wire at control box. I am useing the gmtb-4 bypass I cant seem to figure out where the yellow wire connects. Ithe way I hooked it up Green wire and wire from 86 on the relay to the pink wire. I cut the yellow start motor wire i connected 87a on the relay to one side of the yellow wire and 30 on the relay to the other side of the yellow wire. I have no wire connected to the white wire ignition 2. There is no diode on the relay. I really need some help with this my wife is getting very ugly. What am i doing wrong?
Replies:
Posted By: NowYaKnow
Date Posted: January 05, 2005 at 6:22 AM
You MUST power up the following:
Ignition 1: Pink
Ignition 2: White
Accessory 1: Orange
Starter: Yellow
Mike
Posted By: firefighter321
Date Posted: January 05, 2005 at 6:34 PM
How do i hook up the 556u to a 2003 chevy venture with passkey 3. I tryed to place the ring around the key hole and it just dont seem to work.
Posted By: profuse007
Date Posted: January 05, 2005 at 6:38 PM
how did you wire the bypass?
-------------
Houston,TX
"The two most common elements in the universe are H+ and stupidity" (Ellison).
Posted By: firefighter321
Date Posted: January 05, 2005 at 6:57 PM
red to 12v. black to ground blue to remote starter and ring around the ignition switch
Posted By: firefighter321
Date Posted: January 06, 2005 at 12:07 AM
I am trying to install the rookwood xr-7025. It came with a relay that has two greens, white and a yellow. on the diagram it show the greens to cut the starter wire and tie the relay in to it. then it shows the yellow wire going to the keyhole wire along with a green wire out of the control box. What is the keyhole wire is that ignition 1 or 2. Then it shows a gray wire comeing from the control box hooking up to the start engin wire which ignition is that. This is a 2003 chevy venture. I hook it up like the diagram but when I hit the start engin the acc comes on but no power to the ignition wires. 
Posted By: KarTuneMan
Date Posted: January 06, 2005 at 3:30 AM
Posted By: KarTuneMan
Date Posted: January 06, 2005 at 3:31 AM
I'm not sure about the term "keyhole"........sounds vague and dirty.........ya know
-------------
Posted By: gus1
Date Posted: January 06, 2005 at 11:01 AM
If you pop off the grey turning portion of the switch, you'll see the factory antenna.... try placing your ring directly in front of that antenna. Also, be sure to hook up the green keysense wire to prevent the vehicle from accidentally "seeing" 2 keys at once.
Gus
-------------
Wherever I go, that is where I end up......
Posted By: firefighter321
Date Posted: January 12, 2005 at 9:20 PM
Can anyone help me with finding the door trigger for a 2003 chevy venture.
Posted By: Hymer
Date Posted: January 12, 2005 at 9:49 PM
To avoid the domelight delay use tan for the driver door, blue for the passenger door and the liftgate, and orange for the sliding doors. All wires are negative trigger, located at the BCM and all need to be diode isolated from each other.
-------------
Tire Proz Stillwater Mn
High End Restyling and Comlete Repair
Posted By: firefighter321
Date Posted: January 12, 2005 at 10:03 PM
I haveing problems bypassing PK3 on chevy venture it was working at one time now it is not . anyone have any idea what could of went wrong. I am installing the mannix sm700.
Posted By: SEXIFIED
Date Posted: January 12, 2005 at 10:40 PM
yes, use the dei product #555g data system specific for that venture based on it's year.
don't bother with the 556u it's a great product but the transponder interfeas with the factory system, unless you beak open the keysense wire, and it's really not worth the effort.
change it to the 555g you'll be glad you did.
-------------
SWEET.
Posted By: firefighter321
Date Posted: January 12, 2005 at 11:18 PM
Can someone explain to the proper wireing for the remote starter I am installing a mannix sm700. the way I have it hooked is as follows. If not can you lend a hand and point me in the right direction. also is the 03 chevy venture a type A, b , c or d key cylinder. Red to 12v black to ground i cut the yellow start wire and connected 87a to the start motor side and 30 to the key side yellow. I have 86 from the relay going to pink with the blue from the brain. I have 85 of the relay going to the orange wire from the brain. and 87 of the relay not hooked up.
Posted By: firefighter321
Date Posted: January 13, 2005 at 8:47 AM
I am looking for the netural safty wire for 03 chevy venture. location and color
Posted By: firefighter321
Date Posted: January 19, 2005 at 11:21 PM
Has anyone got the remote start to work? I installing a mannix sm and I am haveing so much trouble . The alarm works good the key is bypassed I removed the bulldog which worked fine so I know the key is bypassed. When I hook up the wires and try it I get 4 chrips on the remote and nothing. It's like nothing is comeing out. Anyone Know which wire goes to where?
|