1999 Mazda 626 Alarm
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=46964
Printed Date: June 01, 2024 at 12:17 PM
Topic: 1999 Mazda 626 Alarm
Posted By: dwahle
Subject: 1999 Mazda 626 Alarm
Date Posted: January 05, 2005 at 10:56 AM
Hi all, I need help in the installation of an alarm with all the bells and whistles. (Rmote start, windows roll down, alarm, etc) for a Mazda 626 4 cylinder (LX) If you have any lessons learned, instructions or any advice it would be appreciated. ------------- Dwahle
Replies:
Posted By: snguyen
Date Posted: January 05, 2005 at 11:34 AM
Remote Starter Wiring Colors and Notes | Function | | Vehicle Color | Location | Start: | | GREEN | IGNITION SWITCH HARNESS | Ignition #1: | | BLACK/ WHITE | IGNITION SWITCH HARNESS | Ignition #2: | | BLACK/ RED | IGNITION SWITCH HARNESS | Ignition #3: | | N/A | | Accessory: | | BLUE | IGNITION SWITCH HARNESS | Brake Light: | | WHITE/ GREEN | AT SWITCH ABOVE BRAKE PEDAL ** | Tach Signal: | | YELLOW | AT COIL MODULE | Parking Lights: | | WHITE/ RED (+) | GREEN PLUG AT FUSE BOX | Headlights: | | N/A | | Diesel Glow Plug: | | | | Clutch Bypass Wire: | | | | Notes: | | ** Brake Wire Also Found In Driver's Kick Panel. |
Alarm and Keyless Entry Wiring Colors and Notes | Function | | Vehicle Color | Location | Constant +12 Volts: | | BLACK | IGNITION SWITCH HARNESS | OEM Alarm Disarm: | | | | Dome Lights/Superv: | | RED / WHITE (-) | AT FUSEBOX | OEM Horn: | | | | Power Lock: | | BROWN / YELLOW (-) | FOUND AT A TAN MODULE NEAR THE HOOD RELEASE | Power Unlock: | | WHITE & BROWN / WHITE (-) | FOUND AT A TAN MODULE NEAR THE HOOD RELEASE*** | Trunk Release: | | ORANGE | ABOVE FUSE BOX | Alarm Input Wire: | | RED / WHITE (-) | AT FUSEBOX | Notes: | | ***The white wire will unlock the drivers door only, and the BROWN / white will unlock the other doors. Use both wires and diode isolate each. See also Note #201 Negative trigger door locks. |
Posted By: dwahle
Date Posted: January 05, 2005 at 12:42 PM
THanks for the information. I don't suppose that you have any installation instructions? Thanks again. ------------- Dwahle
Posted By: snguyen
Date Posted: January 05, 2005 at 12:45 PM
what are you looking for?
Posted By: dwahle
Date Posted: January 05, 2005 at 12:50 PM
Any help or instruction on where to start, and the best way to do it. THanks! ------------- Dwahle
Posted By: DiscoKing
Date Posted: January 05, 2005 at 5:32 PM
I'm actually in the middle of an install on a 1998. Connections went pretty smooth. I started with power connections, then safety cutouts, and then the locks and lights. The only mix up I made was with the + and - parking light wires. Keyless entry is working great but I can't get the Remote Start to do anything. Do you know if the 626 needs an interface module to bypass a transponder? The salesman told the guy I'm doing this for that he didn't need one but I thought it did. That would make sense why the system is not doing anything.
Posted By: DiscoKing
Date Posted: January 05, 2005 at 9:32 PM
Thanks for the info. That didn't work either so I guess I'll have to keep checking wires. The other funny thing I found was that the hood switch has >1 ohm difference between open and closed. Does that make sense cause it doesn't sound like enough to me. Usually switches should have an open reading in one of the positions.
Posted By: DiscoKing
Date Posted: January 08, 2005 at 7:19 PM
Nada. I get absolutely nothing. With key in the ignition and the hood switch disconnected nothing happens. Not even a sound that it is attempting anything. I have double checked the wiring and can find nothing wrong. A bit frustrating. Ugh.
|