03 Taurus Remote start install
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=47622
Printed Date: April 27, 2024 at 4:56 PM
Topic: 03 Taurus Remote start install
Posted By: Reeceddogg
Subject: 03 Taurus Remote start install
Date Posted: January 13, 2005 at 2:02 PM
i was think of getting the Asian wolf FM 2009 DELUXE. i'm familiar with doing everything except the remote start portion of the install since it uses a bypass module. Based on the wiring diagram for an 03 ford taurus listed on the site and the diagram contained with the alarm how would i go about this install
Replies:
Posted By: snguyen
Date Posted: January 13, 2005 at 2:35 PM
One wire at a time .....just post if you run into problem and the folks here will help. Just plan ahead and use a DMM.
Posted By: misterjimbo
Date Posted: January 13, 2005 at 2:36 PM
well... have you done something like this before? like an alalrm or something? what bypass module are you thinking of using?
-------------
Posted By: Reeceddogg
Date Posted: January 14, 2005 at 12:06 AM
yeah i've done quite few alarms and about a dozen or so remote starters but none of them required a bypass module
Posted By: KarTuneMan
Date Posted: January 14, 2005 at 12:18 AM
DEI part # 556U, 556S, or 555U
-------------
Posted By: misterjimbo
Date Posted: January 14, 2005 at 12:50 AM
they are easy to put on on a taurus. i just use a 555u because they have always worked for me.
-------------
Posted By: Reeceddogg
Date Posted: January 14, 2005 at 3:02 AM
would i connect the bypass module to the factory alarm disarm output i have the 555u and 555f. also there's an "armed output(-)500mA what use would i have for this. and for the remote start: ignition 2 output, accessory, ignition 1 output, and start output. also i can't find a wiring diagram for my 03 taurus
Posted By: Reeceddogg
Date Posted: January 14, 2005 at 3:06 AM
would i connect the bypass module to the factory alarm disarm output i have the 555u and 555f. also there's an "armed output(-)500mA what use would i have for this. also i can't find a wiring diagram for my 03 taurus, will the one for a 2000 taurus work that's in the wiring database
Posted By: misterjimbo
Date Posted: January 14, 2005 at 8:55 AM
bypass module to factory alarm disarm? the bypass module is only gonig to have two wires, one is constant and one is negative out when remote started
-------------
Posted By: Reeceddogg
Date Posted: January 14, 2005 at 11:42 AM
so should i connect the bypass module to the factory alarm disarm ouput which is (-)500mA
Posted By: misterjimbo
Date Posted: January 14, 2005 at 1:23 PM
the bypass has two wires correct? one is red and the other is black or blue? the red one goes to constant 12v and the black or blue wire goes to a negative out when running from the remote start. the factory alarm disarm wires has NOTHING to do with the chip in the key. your alarm should have a seperate wire for factory alarm disarm. that goes to i believe a white pink wire in the drivers kick panel.
-------------
Posted By: johnnydi77
Date Posted: January 18, 2005 at 6:31 PM
Disarm is pink/white at the GEM module, and yes you are correct about the transponder override.
-------------
John J. DiStefano Jr.
Posted By: Velocity Motors
Date Posted: January 18, 2005 at 8:34 PM
You have to understand that there are two wires that you need that do totally different things, the DISARM wire disarms the OEM security system from alarming when remote starting and the ground when running /status output goes to the bypass module to turn it on when rmeote start sequence is activated. Both are required for the Taurus and I suggest using a keyless module for the Taurus especially if you live in a climate that is very cold.
-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Posted By: Reeceddogg
Date Posted: January 18, 2005 at 9:57 PM
My DMM just went out on me can someone reccommend a good one
Posted By: Reeceddogg
Date Posted: January 26, 2005 at 11:57 PM
Can somebody give me a wiring diagram something isn't right with the one i have
Posted By: Velocity Motors
Date Posted: January 27, 2005 at 11:26 AM
The one that you got here is correct: https://www.the12volt.com/installbay/forum_posts.asp?tid=19448&KW=Ford+Taurus I did a couple of the 03's and used the same wiring diagram. ------------- Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Posted By: Velocity Motors
Date Posted: January 27, 2005 at 11:30 AM
Use the PKF-3 bypass module for this vehicle. I have used this keyless module with several Ford's and have had 0 problems when installed properly, even in -40 F weather they still operate properly.
-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Posted By: Reeceddogg
Date Posted: February 18, 2005 at 4:16 PM
Where do i get the PKF-3
|